Como deixar HG8245Q2 em modo bridge

Publicado 2019-1-30 15:13:53Última respuesta febr. 11, 2019 01:59:30 1434 1 0 0
  Recompensa Goldies : 0 (solución de problemas)

Mnha ONT HG8345Q2 nao tem a opçao de deixar em modo bridge, teria alguma atualização do firmwere para esse modelo de ONT

  • x
  • convención:

Respuestas destacadas
user_3089457
Publicado 2019-2-11 01:59:30 Útil(0) Útil(0)

hi,

 

you can change the WAN mode to bridge , refer to below snapshot

 

WAN Configuration - bridge
  1. In the navigation tree on the left, choose WAN > WAN Configuration. In the pane on the right, click New. In the dialog box that is displayed, set Mode to Bridge WAN, as shown in Figure 3-18.
    Figure 3-18  WAN Configuration - bridge
    imgDownload?uuid=16be93350290490baacd285
  2. Click Apply.
Table 3-4 describes the parameters related to the WAN in bridge mode.
Table 3-4  Parameters related to the WAN in bridge mode

Parameter

Description

Enable WAN

Indicates whether to enable the WAN connection.

Encapsulation Mode

Indicates the encapsulation mode of a WAN interface. It can be set to IPoE or PPPoE.

Protocol Type

Indicates the protocol type of a WAN interface. It can be set to IPv4, IPv6, or IPv4/IPv6 dual stack.

WAN Mode

Indicates the WAN interface mode. It can be set to Bridge WAN or Route WAN.

Service Type

Indicates the service type of the WAN interface. It is always set to INTERNET.

Enable VLAN

Selects this check box to set VLAN ID and 802.1p priority.

VLAN ID

Indicates the VLAN ID. It ranges from 1 to 4094.

The VLAN ID must be the same as the C-VLAN ID on the OLT.

802.1p Policy

Indicates the 802.1p priority policy.

  • Use specified value: indicates that a specified priority value is used. If you select this option, you need to set the 802.1p parameter.
  • Copy from IP precedence: indicates that the priority is copied from the ToS field in the IP header of the user-side packets. If the received packet is not an IP packet or the packet does not carry the 802.1p priority, the default 802.1p priority is used. If you select this option, you need to set the Default 802.1p parameter.

Binding Options

Used to bind the WAN interface to the LAN port or to the wireless SSID.
NOTE:
Before setting the binding options, set the work mode of the LAN port to route or set the wireless SSID. The binding options can be set only after the work mode or wireless SSID is successfully set. For details, see 3.4.1 LAN Port Work Mode and WLAN Basic Configuration.

Multicast VLAN ID

The multicast VLAN ID ranges from 1 to 4094.

The multicast VLAN ID must be the same as the multicast VLAN ID on the OLT.

imgDownload?uuid=8ce947ee77d54c6e8bfb25c NOTE:
  • WAN in route mode: The ONT functions as a gateway. The IP address of the ONT can be obtained through DHCP, Static, or PPPoE. The IP address of the PC connected to the ONT can be obtained from the DHCP address pool of the ONT or can be set manually.
  • WAN in bridge mode: The ONT functions as a relay and does not process data. The ONT does not obtain the IP address allocated by the upper-layer device and it does not allow manual configuration of a static IP address. The IP address of the device connected to the ONT can be obtained through DHCP, PPPoE, or static.
    • In the case of the DHCP mode, you need to set the DHCP relay. After configuration is complete, the user-side IP address is obtained from the upper-layer device. For the detailed procedure, see 3.4.3 DHCP Server Configuration.
    • In the case of the PPPoE mode, the user-side IP address is obtained through PPPoE authentication of the upper-layer device.
  • x
  • convención:

Good Good Study Day Day Up
Todas las respuestas
user_3089457
user_3089457 Publicado 2019-2-11 01:59:30 Útil(0) Útil(0)

hi,

 

you can change the WAN mode to bridge , refer to below snapshot

 

WAN Configuration - bridge
  1. In the navigation tree on the left, choose WAN > WAN Configuration. In the pane on the right, click New. In the dialog box that is displayed, set Mode to Bridge WAN, as shown in Figure 3-18.
    Figure 3-18  WAN Configuration - bridge
    imgDownload?uuid=16be93350290490baacd285
  2. Click Apply.
Table 3-4 describes the parameters related to the WAN in bridge mode.
Table 3-4  Parameters related to the WAN in bridge mode

Parameter

Description

Enable WAN

Indicates whether to enable the WAN connection.

Encapsulation Mode

Indicates the encapsulation mode of a WAN interface. It can be set to IPoE or PPPoE.

Protocol Type

Indicates the protocol type of a WAN interface. It can be set to IPv4, IPv6, or IPv4/IPv6 dual stack.

WAN Mode

Indicates the WAN interface mode. It can be set to Bridge WAN or Route WAN.

Service Type

Indicates the service type of the WAN interface. It is always set to INTERNET.

Enable VLAN

Selects this check box to set VLAN ID and 802.1p priority.

VLAN ID

Indicates the VLAN ID. It ranges from 1 to 4094.

The VLAN ID must be the same as the C-VLAN ID on the OLT.

802.1p Policy

Indicates the 802.1p priority policy.

  • Use specified value: indicates that a specified priority value is used. If you select this option, you need to set the 802.1p parameter.
  • Copy from IP precedence: indicates that the priority is copied from the ToS field in the IP header of the user-side packets. If the received packet is not an IP packet or the packet does not carry the 802.1p priority, the default 802.1p priority is used. If you select this option, you need to set the Default 802.1p parameter.

Binding Options

Used to bind the WAN interface to the LAN port or to the wireless SSID.
NOTE:
Before setting the binding options, set the work mode of the LAN port to route or set the wireless SSID. The binding options can be set only after the work mode or wireless SSID is successfully set. For details, see 3.4.1 LAN Port Work Mode and WLAN Basic Configuration.

Multicast VLAN ID

The multicast VLAN ID ranges from 1 to 4094.

The multicast VLAN ID must be the same as the multicast VLAN ID on the OLT.

imgDownload?uuid=8ce947ee77d54c6e8bfb25c NOTE:
  • WAN in route mode: The ONT functions as a gateway. The IP address of the ONT can be obtained through DHCP, Static, or PPPoE. The IP address of the PC connected to the ONT can be obtained from the DHCP address pool of the ONT or can be set manually.
  • WAN in bridge mode: The ONT functions as a relay and does not process data. The ONT does not obtain the IP address allocated by the upper-layer device and it does not allow manual configuration of a static IP address. The IP address of the device connected to the ONT can be obtained through DHCP, PPPoE, or static.
    • In the case of the DHCP mode, you need to set the DHCP relay. After configuration is complete, the user-side IP address is obtained from the upper-layer device. For the detailed procedure, see 3.4.3 DHCP Server Configuration.
    • In the case of the PPPoE mode, the user-side IP address is obtained through PPPoE authentication of the upper-layer device.
  • x
  • convención:

Good Good Study Day Day Up

Responder

Responder
Debe iniciar sesión para responder la publicación Inicio de sesión | Registrarse

Aviso Aviso: Para garantizar sus legítimos derechos e intereses, la comunidad y los terceros no publicarán contenido que pueda generar riesgos legales a las partes, por ejemplo, pornografía, contenido político, contenido sobre juego, consumo y tráfico de drogas, así como contenido que viole los derechos de propiedad intelectual de terceros, por ejemplo, secretos comerciales, marcas, derechos de autor, patentes y privacidad personal. No comparta su cuenta ni su contraseña con terceros. Todas las operaciones realizadas usando su cuenta se considerarán como sus acciones y todas las consecuencias que estas acciones generen serán responsabilidad suya. Para obtener información detallada, consulte la “ Política de privacidad.”
Si el botón para adjuntar no está disponible, actualice Adobe Flash Player con la versión más reciente
¡Ingresa y disfruta de todos los beneficios para los miembros!

¡Ingresa y disfruta de todos los beneficios para los miembros!

Aterrizaje