Unable to login to BBU3900

Created: Nov 10, 2019 19:04:11Latest reply: Nov 11, 2019 01:32:16 87 2 0 0
  Rewarded Hi-coins: 1 (problem resolved)

Hi there,


Thank you in advance for the help. I have a BBU3900 chassis with a UPEU and WMPT installed. I am trying to verify the configuration on multiple WBBP boards. After looking at multiple documents I am stuck on how to login to the chassis or even view the local maintenance terminal where the IP address is unknown (192.168.0.49 not working).


Can you provide me direction on how to login to the chassis where the default IP address is not working? Maybe the way is to reset the chassis as it's not in comission? I have my USB to network adapter connected with the IP address set in the proper range on the PC.


Thanks

  • x
  • convention:

Featured Answers
Neil_Tong
Admin Created Nov 11, 2019 01:32:16 Helpful(0) Helpful(0)

Hi dear,
If you want to log in to the BBU3900 chassis, you need to log in to the Web LMT or local LMT through the maintenance IP address of the main control board such as WMPT. If you cannot log in to the main control board using the default maintenance IP (192.168.0.49), check whether the current network is normal.
For example, if you can ping 192.168.0.49 through the local PC, which indicates that the network is normal, otherwise, check whether the network configuration and physical connection are correct.
Besides, the delivered main control board cannot be restored to factory defaults, so if it is necessary, please contact Huawei TAC or R&D engineer to check it further.

  • x
  • convention:

All Answers
wissal
wissal MVE Created Nov 10, 2019 21:37:37 Helpful(1) Helpful(1)

Hello,

- Do you always have problem with this version? If you can get it try to install to your PC.

- Maybe the WMPT has an old SW than you have to upgrade to an earlier version and after the latest.
- The card is faulty

- Try to upgrade via USB port:
1. Create a directory “NodeB” on the USB storage device and inside this directory create two folders “Configuration” and “Software”. Then in Configuration directory you should paste NodeBCfg.xml and in Software directory you should paste Software.csp and SwCPatch.csp files.2.Power on NodeB and wait for 10 minutes.
3. When you find the WMPT RUN light is slowly flash (1s on, 1s off), You must wait for 5 min, then insert Netac USB into the USB port (left one) on the board.
4. When upgrade finished, the BBU will restart automatically, you can hear the voice of fan running loudly for some time.
5. The status of LED:
WMPT RUN slowly flash (1s on, 1s off);
WMPT ACT will be on permanently;
USB LED is on for 2 minutes.
6. Try to connect and verify the SW version.
7. Remove the USB from NodeB



Thanks

  • x
  • convention:

Neil_Tong
Neil_Tong Admin Created Nov 11, 2019 01:32:16 Helpful(0) Helpful(0)

Hi dear,
If you want to log in to the BBU3900 chassis, you need to log in to the Web LMT or local LMT through the maintenance IP address of the main control board such as WMPT. If you cannot log in to the main control board using the default maintenance IP (192.168.0.49), check whether the current network is normal.
For example, if you can ping 192.168.0.49 through the local PC, which indicates that the network is normal, otherwise, check whether the network configuration and physical connection are correct.
Besides, the delivered main control board cannot be restored to factory defaults, so if it is necessary, please contact Huawei TAC or R&D engineer to check it further.

  • x
  • convention:

Comment

Reply
You need to log in to reply to the post Login | Register

Notice Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Login and enjoy all the member benefits

Login and enjoy all the member benefits

Login