Got it

Trunk between Huawei CE6850 & Cisco 3560

Latest reply: Jan 27, 2018 16:51:27 7037 7 0 0

Hi, all!


This post enquires about the trunk between Huawei CE6850 & Cisco 3560. Please see more information below.


Huawei CE6850


ISSUE DESCRIPTION


We've had 2 new Huawei CE6850 switches for a couple of days now and we would like to integrate them with our Cisco core switches (this will also be Huawei's next year).


Cisco 3560

Source: https://www.cisco.com/c/en/us/support/switches/catalyst-3560-series-switches/series.html 


Now, I am trying to set up a trunk between them, but no succes. I hope someone could help - please find below the setups.


CISCO


interface GigabitEthernet0/8
 switchport trunk encapsulation dot1q
 switchport mode trunk


spanning-tree mode rapid-pvst
spanning-tree loopguard default
spanning-tree extend system-id
spanning-tree vlan 1 priority 28672


HUAWEI

  

interface 10GE1/0/48
 port link-type trunk
 port trunk allow-pass vlan all
 stp edged-port enable
 jumboframe enable 9000


What am I missing? Please assist me in setting up the trunk between Huawei CE6850 & Cisco 3560. Thanks!

  • x
  • convention:

user_2790689
Created Oct 27, 2014 10:21:47 Helpful(0) Helpful(0)

Please wait,we'll answer tomorrow morning.

View more
  • x
  • convention:

kellywood
Created Jan 8, 2015 01:55:27 Helpful(0) Helpful(0)

Trunk for Cisco : 

interface GigabitEthernet0/8

 switchport trunk encapsulation dot1q
 switchport mode trunk


spanning-tree mode rapid-pvst

spanning-tree loopguard default
spanning-tree extend system-id
spanning-tree vlan 1 priority 28672


If you want to know more about Cisco 3560 switch , you can follow Router-Switch.

View more
  • x
  • convention:

123121313
Created Oct 28, 2014 08:27:26 Helpful(0) Helpful(0)

spanning-tree mode rapid-pvst
// it should use starnd stp mode , pvst is cisco private protocol;

 

interface 10GE1/0/48
 port link-type trunk
 port trunk allow-pass vlan all
 stp edged-port enable  // no need to use this command,it is for the port connecting terminal device

 

btw, GigabitEthernet0/8-----------10GE1/0/48
GE to 10GE , make sure the optical modules are correct.

 

View more
  • x
  • convention:

admin.sioux
Created Oct 28, 2014 08:31:03 Helpful(0) Helpful(0)

Quote 3 #

These switches are UTP switches so no needs for modules :) according to huawei it should work with rapid-pvst of cisco.


spanning-tree mode rapid-pvst
// it should use starnd stp mode , pvst is cisco private protocol;

 

interface 10GE1/0/48
 port link-type trunk
 port trunk allow-pass vlan all
 stp edged-port enable  // no need to use this command,it is for the port connecting terminal device

 

btw, GigabitEthernet0/8-----------10GE1/0/48
GE to 10GE , make sure the optical modules are correct.

 

c00193773 Post On 2014-10-28 08:27

View more
  • x
  • convention:

admin.sioux
Created Oct 29, 2014 10:49:21 Helpful(0) Helpful(0)

See below, unfortunatelly it is not working with the above config.

------------------

Interoperation Networking Design


PVST+ is a Cisco proprietary protocol that uses a Cisco reserved multicast MAC address. 
Huawei switches do not support Cisco PVST+. The following methods can implement 
interoperation between Cisco PVST+ switches and Huawei switches:


? On a trunk port, Cisco PVST+ sends two types of BPDUs in VLAN 1: untagged Cisco 
PVST+ proprietary BPDUs and standard RSTP BPDUs. Huawei switches can identify 
RSTP BPDUs. When a Huawei switch connects to a trunk port of a Cisco PVST+ switch, 
enable RSTP or MSTP on the Huawei switch so that it can work with the Cisco PVST+ 
switch.


? On an access port, Cisco PVST+ sends standard BPDUs. When a Huawei switch 
connects to an access port of a Cisco RVST+ switch, enable RSTP or MSTP on the 
Huawei switch.


? (Not recommended) Huawei switches forward Cisco PVST+ BPDUs as service packets 
to access the Cisco PVST+ network. In this mode, the blocked ports are located on Cisco 
switches
--------------

View more
  • x
  • convention:

rickthomas
Created Jan 10, 2018 23:10:01 Helpful(0) Helpful(0)

  If you are looking for Cisco switch trunking support you can try NetEquity.com.  They sell and support
used cisco switches and are an excellent support resource. This post was last edited by user_2987913 at 2018-01-10 23:12.
View more
  • x
  • convention:

uzzi
Created Jan 27, 2018 16:51:27 Helpful(0) Helpful(0)

I had similar issue, try using VBST on huawei, that will work :)

Please do not hesitate to leave message in case of any further assistance.
View more
  • x
  • convention:

Kindest%20Regards%3Cbr%20%2F%3E%0AMuhammad%20Uzair%3Cbr%20%2F%3E%0AHCIE%20%23677

Comment

You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."

My Followers

Login and enjoy all the member benefits

Login

Huawei Enterprise Support Community
Huawei Enterprise Support Community
Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.