Got it
Enterprise
Community Forums Switches
Too many discards on inte...

Too many discards on interface 10GE

Created: Mar 25, 2019 10:57:46Latest reply: Aug 29, 2019 05:46:59 1290 3 1 0
  Rewarded HiCoins： 0 (problem resolved)
display all floors #1

Hello!We have a two CE6880-24S4Q2CQ-EI switches installed and we are seeing discarded packet on 10GE interfaces (between switches and connected servers), although the links are not fully loaded.

<HW1>display interface 10GE 1/0/12
10GE1/0/12 current state : UP (ifindex: 16)
Line protocol current state : UP
Switch Port, PVID :    1, TPID : 8100(Hex), The Maximum Frame Length is 9216
Internet protocol processing : disabled
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is a4be-2b09-xxxx
Port Mode:     COMMON FIBER,     Port Split/Aggregate:         DISABLE
Speed:                10000,     Loopback:                        NONE
Duplex:                FULL,     Negotiation:                  DISABLE
Input Flow-control: DISABLE,     Output Flow-control:          DISABLE
Mdi:                      -,     Fec:                             NONE
Last physical up time   : 2019-01-21 06:54+03:00
Last physical down time : 2019-01-21 06:54+03:00
Current system time: 2019-01-21 06:54+03:00
Statistics last cleared:2019-01-21 06:54+03:00
    Last 300 seconds input rate: 62588928 bits/sec, 6921 packets/sec
    Last 300 seconds output rate: 70494505 bits/sec, 7872 packets/sec
    Input peak rate 104529722 bits/sec, Record time: 2019-01-21 06:54+03:00
    Output peak rate 143899302 bits/sec, Record time: 2019-01-21 06:54+03:00
    Input :        14360427480 bytes,           12670107 packets
    Output:        21399136744 bytes,           17577164 packets
    Input:
      Unicast:               12661977,   Multicast:                    1937
      Broadcast:                 6193,   Jumbo:                     8491287
      Discard:                      0,   Frames:                          0
      Pause:                        0
      Total Error:                  0
      CRC:                          0,   Giants:                          0
      Jabbers:                      0,   Fragments:                       0
      Runts:                        0,   DropEvents:                      0
      Alignments:                   0,   Symbols:                         0
      Ignoreds:                     0
    Output:
      Unicast:               17555265,   Multicast:                   12699
      Broadcast:                 9200,   Jumbo:                    13076063
      Discard:                   9040,   Buffers Purged:                  0
      Pause:                        0

    Input bandwidth utilization threshold : 90.00%
    Output bandwidth utilization threshold: 90.00%
    Last 300 seconds input utility rate:  0.62%
    Last 300 seconds output utility rate: 0.70% We are make QOS settings on interface, as recommended on huawei forum, but no effect. interface 10GE1/0/12
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 4, 5, 6
 qos burst-mode enhanced
 device transceiver 10GBASE-FIBER


  • x
  • convention：

I have this problem too (1) Favorite(0) Share Report
Previous: Huawei enterprise network highlighted posts collection - Issue 2
Next: How to prevent users from configuring static IP addresses without permission
Featured Answers

Recommended answer

(1) (1)
Mohamed_Mostafa
Created Mar 25, 2019 11:19:07 Helpful(1) Helpful(1)

Hi!

It seems like there are a lot of jumbo frames.

 Too many discards on interface 10GE-2897201-1

Please check:

Setting the Jumbo Frame Length Allowed on an Interface

Also, you can check the display interface transceiver for more errors or alarms:
View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
Network%20%26%20Security%20Engineer
All Answers
Mohamed_Mostafa
Mohamed_Mostafa Created Mar 25, 2019 11:19:07 Helpful(1) Helpful(1)

Hi!

It seems like there are a lot of jumbo frames.

 Too many discards on interface 10GE-2897201-1

Please check:

Setting the Jumbo Frame Length Allowed on an Interface

Also, you can check the display interface transceiver for more errors or alarms:
View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
Network%20%26%20Security%20Engineer
chenhui
chenhui Admin Created Mar 26, 2019 06:23:43 Helpful(0) Helpful(0)

@serge_s76 hello,
from the output of the command display, the output discard means the packets discarded by the interface during physical layer detection due to queue congestion,
it seems that the burst traffic has exceed the buffer size.
View more
  • x
  • convention：
user_3534923
user_3534923 Created Aug 29, 2019 05:46:59 Helpful(0) Helpful(0)

<HW1>display interface 10GE 1/0/12 10GE1/0/12 current state : UP (ifindex: 16) Line protocol current state : UP Switch Port, PVID :    1, TPID : 8100(Hex), The Maximum Frame Length is 9216 Internet protocol processing : disabled IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is a4be-2b09-xxxx Port Mode:     COMMON FIBER,     Port Split/Aggregate:         DISABLE Speed:                10000,     Loopback:                        NONE Duplex:                FULL,     Negotiation:                  DISABLE Input Flow-control: DISABLE,     Output Flow-control:          DISABLE Mdi:                      -,     Fec:                             NONE Last physical up time   : 2019-01-20 22:54+03:00 Last physical down time : 2019-01-20 22:54+03:00 Current system time: 2019-01-20 22:54+03:00 Statistics last cleared:2019-01-20 22:54+03:00     Last 300 seconds input rate: 62588928 bits/sec, 6921 packets/sec     Last 300 seconds output rate: 70494505 bits/sec, 7872 packets/sec     Input peak rate 104529722 bits/sec, Record time: 2019-01-20 22:54+03:00     Output peak rate 143899302 bits/sec, Record time: 2019-01-20 22:54+03:00     Input :        14360427480 bytes,           12670107 packets     Output:        21399136744 bytes,           17577164 packets [align=(left|center|right)] 
[align=(left|center|right)]This the featured and inner advancement specification https://support.huawei.com/hedex/pages/EDOC110005400031180APG/04/EDOC110005400031180APG/04/resources/dc/dc_cfg_int_1019.html?ft=0&fe=10&hib=6.5.3.5.14&id=EN-US_TASK_0141109363&text=Setting the Jumbo Frame Length Allowed on an Interface&docid=EDOC1100054000.
[align=(left|center|right)]For more information  about Data Related visit https://uaedatarecovery.com/data-recovery-dubai/
View more
  • x
  • convention：
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Copyright © 2021 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.