tAPP810 Video Service

This section describes the operations of the video service on a tAPP810.

1. Video Call

This section describes operations related to video calls performed on a tAPP810.

Procedure

· Answering a Video Call

1. When a video call is incoming, slide to receive the video call.

2. After a call is connected, you can set the following parameters: mute, close the local video.

3. After a PTP video call is complete, touch the on the home screen to terminate the call.

· Making a Video Call

1. On the home screen of the tAPP810, tap .

2. Use one of the following methods to make a PTP video call:

§ Enter a call number on the Dialer, touch .

§ Enter Recents. Select a PTP video call number for redialing.

§ Enter Recents. Select a call record and touch to view details. Touch .

§ Touch in the upper right corner of the PTP message detail page and then select .

3. After the PTP video call is connected, you can set the call-related parameters. For details, see Answering a Video Call.

4. After a PTP video call is complete, touch the on the home screen to terminate the call.

2. Video Surveillance

This section describes operations related to video surveillance performed on a tAPP810.

Procedure

· Making a Video Surveillance

1. On the home screen of the tAPP810, touch to enter Video surveillance.

2. Use one of the following methods to originate video surveillance:

§ Enter a terminal number and then touch Surveillance.

§ Select History. Select a video surveillance number for redialing.

§ Select Camera/Contacts. You can view the camera and contact list, and select a contact number to initiate a video surveillance.

NOTE:

The camera list is downloaded from the network and cannot be modified on the terminal.

3. During video surveillance, you can set the following parameters:

§ Loudspeaker

§ Rotatable component. The video display ratio remains unchanged with a screen-adaptive width.

§ If the camera supports Pan Tile Zoom (PTZ) control, adjusting of camera direction and focal length through PTZ control is supported.

4. After video surveillance is complete, touch to stop it.

3. Video Distribution

This section describes operations related to video distribution performed on a tAPP810.

Procedure

· Answering a Video Distribution

1. When a video distribution is incoming, the home screen displays call initiator information. Press Answer to receive the distribution.

2. After a video distribution is connected, the screen for video distribution is displayed. You can set the loudspeaker using a key.

3. A video distribution automatically ends when it is complete. You can also touch the end icon below the video to terminate a video distribution.

· Making a Video Distribution

Only a dispatcher operator can initiate video distribution. No operations are required at the UE.

4. Video Sending

This section describes operations related to video sending performed on a tAPP810.

Context

· If the video file sent back is in widescreen mode and portrait view, the UE should be held horizontally, with the home key on the right side.

Handheld direction

· If you send videos using the front-facing camera, you cannot adjust the focal length.

· During the video upload, the front-rear switchover is available only when both the front and rear cameras support the current resolution.

Procedure

· Video Sending

1. On the home screen, touch to enter the video sending application. Icons in the operation bar are listed in Table.

Table Icons in the operation bar

Icon	Function
/	Enable/disable the flashlight.
	Switch to the front or rear camera.
	Set video sending parameters.
/	Upload a video/photo. Slide leftward or rightward to switch between photo sending and video sending. Local videos/photos will be recorded when the user is offline.
	Enter the local album to preview or initiate offline upload photos or videos.
	View the video sending history.

2. Touch to set video sending parameters.

Parameter descriptions

Parameter	Description
Confirm before video sending	If the switch is turned on, you need to confirm when other UEs or a dispatcher send a video surveillance request over your UE.
Record if network unavailable	If the switch is turned on, recording is performed automatically when the network is unavailable.
Dispatcher ID	If the video sending number is not configured, the number is 99999500 by default.
Resolution	Specify the resolution.
White balance	Specify the white balance.
Preferred storage location	Specify the save path for files.
Restore to defaults	Restore parameters to defaults.