SmartAX MA5633 Port Description

Gavin.Liu · Created Dec 19, 2018 03:41:09

very good！

Torrent · Created Dec 25, 2018 01:26:47

The modular MA5633 provides two uplink optical ports and one GE electrical port. Either uplink optical port 0 or the GE electrical port can be used at a time.

**: indicates the optical RX port on the built-in optical receiver, without the RX silkscreen.

thanks for sharing

yjhd · Created Dec 26, 2018 01:35:14

The modular MA5633 provides two uplink optical ports and one GE electrical port. Either uplink optical port 0 or the GE electrical port can be used at a time.

Finn92 · Created Dec 29, 2018 01:43:34

Introduces the 220 V AC or 60 V AC power to the MA5633.
NOTE
Block this port if you do not use it. Replace this port with an F connector when the MA5633 uses the 60 V AC power supply.

lizhi94 · Created Dec 29, 2018 01:53:32

have got the point
The modular MA5633 provides two uplink optical ports and one GE electrical port. Either uplink optical port 0 or the GE electrical port can be used at a time.
we have learn the MA5633 device indicates the optical RX port on the built-in optical receiver, without the RX silkscreen.
thanks for your solution
we have learn the MA5633 device indicates the optical RX port on the built-in optical receiver, without the RX silkscreen.
thanks for your solution

SupperRobin · Created Dec 29, 2018 03:15:08

Controls RF port status. The MA5633 supports two-status and three-status configurations. The two statuses are enable and disable and the three statuses include attenuation more compared with the two statuses. The two statuses work with the upstream spectrum scanning function provided by the U2000. In this way, the MA5633 can rapidly identify an RF line where a noise source locates, thereby improving troubleshooting efficiency.

littlestone · Created Dec 29, 2018 06:15:28

SmartAX MA5633 is a CMC device based on DOCSIS3.0 and DOCSIS3.1 protocol. It is mainly aimed at the digitization and two-way transformation of cable TV network. It can provide broadcasting operators with high bandwidth and multi-service access

w1 · Created Dec 31, 2018 14:20:03

The description of so many port are very detailed, they are very useful for troubleshooting issue, thanks for yoru sharing, i think i can analyize and fix issue faster by refering to this post, thanks again

Port Type	Silkscreen	Description	Quantity (MA5633 Working with an External Optical Receiver/External Optical Receiver+Built- in EQAM)	Quantity (MA5633 Equipped with a Built-in Optical Receiver or Built-in Optical Receiver&WDM or Built-in Optical Receiver&WDM&EQAM)	Quantity (MA5633 Equipped with a Built-in Optical Transceiver&WDM &EQAM)
Power port	Power	Introduces the 220 V AC or 60 V AC power to the MA5633. NOTE Block this port if you do not use it. Replace this port with an F connector when the MA5633 uses the 60 V AC power supply.	1	1	1
Uplink optical port	OPTICAL	Provides one uplink port, which can be a GPON or GE port, which uses a small form-factor pluggable (SFP) module.	Non-modular MA5633: 1 Modular MA5633: 2*		2*
GE electrical port	GE	Used for upstream transmission.	1
Optical port on the built-in optical receiver	RX**	Can only be of the SC/APC type	0	1	1
Optical TX port on the built-in optical transceiver	TX	Can only be of the SC/APC type.	0	0	1
Commissioning serial port	CONSOLE	Supports local maintenance and remote maintenance.	1	1	1
Maintenance Ethernet port	ETH	A 100M Base-T commissioning Ethernet port and supports 100M full-duplex autonegotiation.	1	1	1
RF port	RF	Inputs and outputs CATV and Ethernet signals.	2-in-2-out or 4-in-4-out	2-out or 4-out	4-out

SmartAX MA5633 Port Description

Third Party’s Trade Secret

My Followers

Enterprise

Consumer

Corporate

Carriers

SmartAX MA5633 Port Description

Third Party’s Trade Secret

My Followers