S5720-28TP-PWR-LI-ACL

Latest reply: Apr 10, 2019 15:31:47 201 6 0 0

How to restore factory settings? Access level is mistakenly set to 15. Only diagnostic mode is available.


  • x
  • convention:

Admin Created Apr 9, 2019 10:11:39 Helpful(0) Helpful(0)

what's your firmware version? if it is newer than V200R012C00
the PNP button on the switch can be reused to reset the switch.
To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.
To reset the switch, press the button.
Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
  • x
  • convention:

Created Apr 9, 2019 16:31:36 Helpful(0) Helpful(0)

String from switch boot log:
Now, the current startup file is flash:/s5720li-v200r010c00spc600.cc
  • x
  • convention:

Created Apr 9, 2019 16:38:57 Helpful(0) Helpful(0)

This is the complete switch boot log by the console.

BIOS loading ...
DDR3 Training Sequence - Ver TIP-42.H-1.0.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED


U-Boot (Jan 05 2017 - 10:08:40)


The press of Ctrl+T before TEST is room test
Press Ctrl+T to Start Memory Test: 0
Board: ES5D2V28S011
NAND: 512 MB
Using default environment

FPU initialized to Run Fast Mode.
USB2.0 0: Host Mode
Net: egiga0 [PRIME], egiga1

Boot from main : boot num[1]

Starting kernel ...Get log address 0xe0a80050




INIT: version 2.88 booting
Starting udev
Starting Bootlog daemon: bootlogd.
Populating dev cache
INIT: Entering runlevel: 3ge = 5
Stopping Bootlog daemon: bootlogd.

Wind River Linux 6.0.0.30 localhost console

localhost login: root (automatic login)
login[1919]: root login on 'console'

Jan 23 2017, 19:21:20
mknod: /dev/mvPP: File exists
BootLoad version : 020a.0001
Backup U-Boot ............................................................. done

Press Ctrl+B or Ctrl+E to enter BootLoad menu: 0
Now, the current startup file is flash:/s5720li-v200r010c00spc600.cc

Info: Check signature, please wait.................


System total memory is 0x15200000

Start to initialize the LSW ...
Initializing the LSW ...................................................... done
Initializing netlink ...................................................... done
Initializing fast netlink ................................................. done
Backup BootLoad ........................................................... done
Backup Kernel ............................................................. done
Backup RamDisk ............................................................ done

Stack status : enable
ECM Stack status : run

Initializing FSP task begin ...

Initializing DEV module ................................................... done

Initializing hardware system .............................................. done
Begin to start the system ...

Registering IPC and VP callback to platform ............................... done

Initializing VFS ..................................... Done
Checking startup system-software .......................................... done
Reading PAF file .......................................................... done
Initializing VOS monitor ............................. Done
CFM initialization advance ........................... done
Initializing PAT ..................................... Done
Initializing HA ...................................... done
VFS registering to HA ................................ Done

VRP root begin ...
VRP root end
CFG initialization begin ............................. done
CFM initialization begin ............................. done
CLI initialization begin ............................. done
Registering VRP all link command begin ............... Done
Creating task begin ...
Creating task end
Task initialization begin ...
Task initialization end

ECMM status : run
Cmd registering begin ...
Cmd registering end

Task awake begin ...
Task awake end

Recover configuration begin ...
Recover configuration end
Press ENTER to get started.


Login authentication


Username:admin
Password:
Error: Authentication fail

Username:admin
Password:
<5720-28tp>?
User view commands:
display Display current system information
hwtacacs-user HWTACACS user
local-user Add/Delete/Set user(s)
lock Lock the current user terminal interface
mmi-mode Machine-machine mode
ping Send echo messages
quit Exit from current command view
reset Reset operation
return Exit to user view
save Save file
super Privilege current user a specified priority level
telnet Establish a Telnet connection
terminal Set the terminal line characteristics
trace Trace route (switch) to host on Data Link Layer
tracert Trace route to host
undo Cancel current configuration

<5720-28tp>
  • x
  • convention:

Created Apr 9, 2019 17:52:05 Helpful(0) Helpful(0)

Is it possible to get a link to a guide for restoring factory settings for this model S5720-28TP-PWR-LI-ACL?
  • x
  • convention:

Created Apr 9, 2019 20:47:58 Helpful(0) Helpful(0)

my version v200r010c00
  • x
  • convention:

Created Apr 10, 2019 15:31:47 Helpful(0) Helpful(0)

problem solved
  • x
  • convention:

Reply

Reply
You need to log in to reply to the post Login | Register

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!

Login and enjoy all the member benefits

Login
Fast reply Scroll to top