Got it
Huawei Enterprise Support Community
Community Forums Routing & Switching
S1720-GWR-4P setting inb...

S1720-GWR-4P setting inbound outbound limits by snmp

Created: Feb 2, 2021 00:39:12Latest reply: Feb 2, 2021 06:50:44 319 6 0 0 1
  HiCoins as reward： 0 (problem unresolved)
View the author 1#

Hi,

I'm searching for solution to set in/out bandwidth limits per interface by snmp on switch S1720-GWR-4P

Software      Version   : VRP (R) Software, Version 5.170 (V200R019C10SPC500)

patch: s1720-gw-v200r019sph016


Interface config example:

interface GigabitEthernet0/0/1
 qos lr outbound cir 208000 cbs 2400000
 qos lr inbound cir 208000 cbs 2400000


I found that i can set inbound cir value with this OID

like this .1.3.6.1.4.1.2011.5.25.32.4.1.1.26.1.4.5.1.1 i 208000

but i can't set outbound as described in MIB, it should be by changing indexes

probably like .1.3.6.1.4.1.2011.5.25.32.4.1.1.26.1.4.5.2.1 i 208000 but this doesn't work.


.1.3.6.1.4.1.2011.5.25.32.4.1.1.26.1.4.5.2.1 i 208000

Error in packet.
Reason: (genError) A general failure occured
Failed object: SNMPv2-SMI::enterprises.2011.5.25.32.4.1.1.26.1.4.5.2.1


NamehwXQoSCarCirValue
OID.1.3.6.1.4.1.2011.5.25.32.4.1.1.26.1.4
MIBHUAWEI-XQoS-MIB
SyntaxINTEGER32 (0..100000000)
Accessread-create
Statuscurrent
DefVal
IndexeshwXQoSCarInterfaceIndex, hwXQoSCarDirection, hwXQoSCarVlanID
DescrThe value of this object identifies the CIR on an interface.


when it's set on interface i can see correct value in snmpget on OID  .1.3.6.1.4.1.2011.5.25.32.4.1.2.5.1.3.5.1

but i can't change there either:

.1.3.6.1.4.1.2011.5.25.32.4.1.2.5.1.3.5.1 i 208000

Error in packet.
Reason: (genError) A general failure occured
Failed object: SNMPv2-SMI::enterprises.2011.5.25.32.4.1.2.5.1.3.5.1

OID description:


NamehwXQoSIfLrCir
OID.1.3.6.1.4.1.2011.5.25.32.4.1.2.5.1.3
MIBHUAWEI-XQoS-MIB
SyntaxINTEGER32
Accessread-create
Statuscurrent
DefVal
IndexeshwXQoSIfLrCfgIfIndex, hwXQoSIfLrCfgVlanID
DescrThis object indicates the CIR. The value ranges from 1 to the interface bandwidth.
snmpsetsnmp oidS1720

Like (0) Dislike (0) Favorite(1) Share Report
Previous: Reduce the number of LSPs
Next: Port Security
Featured Answers

Recommended answer

(0) (0)
DDSN
Admin Created Feb 2, 2021 01:30:11

Hi gedas965,
Currently, the maximum access permission of hwXQoSIfLrCfgInfoTable is read-only.

1

You can refer to：https://support.huawei.com/hedex/hdx.do?docid=EDOC1100126530&id=EN-US_CONCEPT_0177125612&lang=en

I hope it helps!

View more
  • x
  • convention：

gedas965
gedas965 Created Feb 2, 2021 10:09:47 (0) (0)
i can't implement huawei to existing management system without rate limiting on interface. So for now i have to stay with old sw brand...
is there any chance that feature setting "qos lr outbound cir" by snmp gets implemented in new firmware or patch versions?  
DDSN
DDSN Reply gedas965  Created Feb 3, 2021 01:12:35 (0) (0)
After checking the latest version, I find that this function is not supported. You can directly contact the TAC to raise the requirement.  
All Answers
(0) (0)
2#
DDSN
DDSN Admin Created Feb 2, 2021 00:40:49

Hi gedas965,
Please wait patiently. Our engineers are looking for answers to your questions.
View more
  • x
  • convention：
(0) (0)
3#
DDSN
DDSN Admin Created Feb 2, 2021 01:30:11

Hi gedas965,
Currently, the maximum access permission of hwXQoSIfLrCfgInfoTable is read-only.

1

You can refer to：https://support.huawei.com/hedex/hdx.do?docid=EDOC1100126530&id=EN-US_CONCEPT_0177125612&lang=en

I hope it helps!

View more
  • x
  • convention：

gedas965
gedas965 Created Feb 2, 2021 10:09:47 (0) (0)
i can't implement huawei to existing management system without rate limiting on interface. So for now i have to stay with old sw brand...
is there any chance that feature setting "qos lr outbound cir" by snmp gets implemented in new firmware or patch versions?  
DDSN
DDSN Reply gedas965  Created Feb 3, 2021 01:12:35 (0) (0)
After checking the latest version, I find that this function is not supported. You can directly contact the TAC to raise the requirement.  
(0) (0)
4#
Abdussamed
Abdussamed Created Feb 2, 2021 06:50:44

Gedas965 Change SNMP versiyon and check parameters?
I will suggest you pass SNMPv3
View more
  • x
  • convention：

gedas965
gedas965 Created Feb 2, 2021 10:15:03 (0) (0)
tried snmpv3 same error, so that's probably not implemented to be set by snmp  
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.