reset ME60 or reset its console password

Hi@MohamedAliKhouja,

I checked the document, and there is no introduction to each step in the document. If you want to reset the router or reset the console password, you can refer to the document link https://support.huawei.com/enterprise/en/doc/EDOC1000175918/b0a7dacb
Hope to help you!

Hi,
Selected 3

https://support.huawei.com/enterprise/en/doc/EDOC1000175918/b0a7dacb

Select 3. 

1. Select 3. Enter ethernet submenu to access the Ethernet submenu.

           Ethernet Submenu
   
   
        1. Install OS through ethernet interface
   
        2. Install OS Format Hard Disk
   
        3. Boot OS through ethernet interface
   
        4. Modify ethernet interface boot parameters
   
        5. Return
   
   
     Note: Need to open tftp & ftp tools both while downloading.
   
   
   Enter your choice(1-5):

2. Select 4. Modify ethernet interface boot parameters to set the server address and password and specify the file to be downloaded. In this situation, the FTP server must be connected to the device through a management network interface.

   

   Enter your choice(1-5): 4server ip     : 10.1.30.5    -  //Address of the FTP/TFTP server.
   
   target ip     : 10.1.10.16    -  //Address of the current MPU. 
   
   gateway ip    : 10.1.1.1      -  //Gateway address.
   
   net mask      : 255.255.0.0      -  //Mask value.
   
   file name     : V800R013C00SPC100-OC-NE-X8X16.cc  -  //Name of the system software package.
   
   ftp or tftp   : ftp              -  //Select FTP or TFTP.
   
   user name     : HUAWEI             -  //FTP user name.
   
   user password : ******           -  //FTP password.

• The management network interface is usually located on the chassis or MPU of a device. The name of the management network interface may vary according to the device, such as ETH/OAM, ETH, and MGMT-ETH. For details, see the hardware description of the corresponding product.

• You can deploy an independent FTP/TFTP server or configure a local PC as an FTP/TFTP server.

• If an independent FTP/TFTP server is used, ensure that the FTP/TFTP server is physically connected to the device.

• Both FTP and TFTP services must be enabled during the upgrade. Therefore, specifying the same working path for the FTP and TFTP services is recommended.

After setting the parameters, select 2. Install OS and Format Hard Disk to format the CF card. Wait until the device is started.

If no backup is available, the configuration file will be lost after the CF card is formatted. To avoid this situation, select 1. Install OS through ethernet interface. When uploading the new configuration file, ensure the uniqueness of the file name.

Ethernet Submenu      1. Install OS through ethernet interface      2. Install OS and Format Hard Disk      3. Boot OS through ethernet interface      4. Modify ethernet interface boot parameters      5. Return   Note: Need to open tftp & ftp tools both while downloading.Enter your choice(1-5): 2

Tftp download file V800R013C00SPC100-OC-NE-X8X16.cc OK!

Tftp download file V800R013C00SPC100-OC-NE-X8X16.cc OK!


 install_os_from_net init start flag! 


Startup file: V800R013C00SPC100-OC-NE-X8X16.ccConfig  file:/opt/vrpv8/home/vrpcfg.zip


Paf     file:/opt/vrpv8/home/


License file:


Patch   file:


Now reset all other slot

Master MPU Reset Other Board ..................... pass

Set Bootargs Env ................................. pass

Loading Kernel Image ............................. pass

Loading Ramdisk Image ............................ pass

Loading FDT Image ................................ pass

[   58.992701] hd 0:0:0:0: [hda] Assuming drive cache: write through

Loading, please [   59.072972] hd 0:0:0:0: [hda] Assuming drive cache: write through

wait...

cx68mpu[   59.170734] hd 0:0:0:0: [hda] Assuming drive cache: write through

k

wait for storage device node...

storage device node probe done...


Press CTRL+K to enter Kernel Menu..1s

Check file system, this may take a few minutes ... 

*[   60.558392] hd 0:0:0:0: [hda] Assuming drive cache: write through

***************************************

Check file system .... ok.

rootfs loading, please wait...

Now starting VRPV8 ........


Please press Enter to activate this console. 

User interface con0 is available

Thanks