This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>

Enterprise
Community Forums Switches
Renumber stand alone huaw...

Renumber stand alone huawei switch S5700

Latest reply: May 18, 2018 01:03:29 1149 2 0 0
display all floors #1
Hi,


I think that the title is clear enough.

I'm trying to configure a single switch (not in stack) and I would like to know how to renumber interfaces.

Example : 

GigabitEthernet 0/0/1 => GigabitEthernet 1/0/1

I found few commands as stack slot ID renumber ... but my switch is a "stand alone" one.

Thank you in advance.

Best regards,

Simon
  • x
  • convention：

Helpful (0) Favorite(0) Share Report
Created May 17, 2018 13:57:30 Helpful(0) Helpful(0)

Why would you want to do that? :)
For standalone switches I doubt this function is available.
  • x
  • convention：
“We only get answers to the questions that we ask.” physicist Werner Heisenberg
Created May 18, 2018 01:03:29 Helpful(0) Helpful(0)

In my opinion, this switch may establish a stack before. When we split a Stack, we need follow these steps.
http://support.huawei.com/hedex/hdx.do?lib=EDOC1000161579DEG0801J&docid=EDOC1000161579&lang=en&v=04&tocLib=EDOC1000161579DEG0801J&tocV=04&id=dc_cfg_istack_1053&tocURL=resources%2fdc%2fdc%5fcfg%5fistack%5f1053%2ehtml&p=t&fe=1&ui=3&keyword=a&keyword=stack&keyword=split&text=%25253Cb%25253ESplitting%25253C%25252Fb%25253E%252B%25253Cb%25253Ea%25253C%25252Fb%25253E%252B%25253Cb%25253EStack%25253C%25252Fb%25253E

Splitting a Stack

Context

If a stack is no longer used, you can split the stack into standalone switches. Stacks established using stack card connections and service port connections are split in different ways. A split process includes the following steps.
1.Back up the stack configuration file.
2.Remove stack cables.
3.Restore physical member ports to service ports. (This step is required only in service port stacking.)
4.Restore the stack ID to the default value.
5.Power off all the member switches.
6.Remove the stack card. (This step is required only in stack card stacking.)

Procedure
•Splitting a stack established with stack card connections 1.Run the save command to save the configuration.
2.Run the copy source-filename destination-filename all command to back up the configuration file to all the member switches, so that you can use the configuration file when you set up a stack the next time.
3.Remove stack cables between the member switches. After you remove the stack cables, the stack splits and some member switches restart. The remote login may fail because some configurations of member switches such as the IP address are the same. Log in to a switch through the console port to perform configurations.
4.Run the system-view command to enter the system view.
5.Run the stack slot slot-id renumber 0 command to restore the stack ID of a member switch to the default value 0.
6.Power off all the member switches.
7.Remove the stack card.

•Splitting a stack established through service port connections 1.Run the save command to save the configuration.
2.Run the copy source-filename destination-filename all command to back up the configuration file to all the member switches, so that you can use the configuration file when you set up a stack the next time.
3.Remove the stack cables between the member switches. After you remove the stack cables, the stack splits and some member switches restart. The remote login may fail because some configurations of member switches such as the IP address are the same. Log in to a switch through the console port to perform configurations.
4.Run the system-view command to enter the system view.
5.Run the interface stack-port member-id/port-id command to enter the logical stack port view.
6.Run the shutdown interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> command to disable physical member ports.
7.Run the undo port interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> enable command to restore physical member ports to service ports.
8.Run the quit command to exit from a logical stack port.
9.Run the stack slot slot-id renumber 0 command to restore the stack ID of a member switch to the default value 0.
10.Power off all the member switches.
  • x
  • convention：
Back to list

Reply

Reply
Advanced
B Color Image Link Quote Code Smilies
You need to log in to reply to the post Login | Register

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy Terms of Use
Huawei Enterprise Huawei Carrier Forum Training & Certification

Copyright © 2019 Huawei Technologies Co., Ltd. All rights reserved.

Fast reply Scroll to top