registration third-party GPON ONT with huawei OLT GPON

liqiang185 · Created Oct 14, 2019 06:55:19

Hello, please refer to the following two links, which are introduced in great detail.

https://forum.huawei.com/enterprise/en/is-it-necessary-to-have-an-interoperability-file-to-add-a-third-party-ont-to-the-olt/thread/559235-100181

https://forum.huawei.com/enterprise/en/how-to-add-3-rd-party-ont-to-huawei-olt-ma5608t/thread/486989-100181

wissal · Created Oct 13, 2019 20:29:21

Hello，

Interworking with third-party ONTs requires a license and an interworking file;

Then use this command：load ont-interoperability-file;

So you need the help of your OLT provider.

Usage Guidelines

If a command for loading, backing up, duplicating, or saving a file is being executed, the execution of this command fails.
Before loading a file, ensure that the TFTP, FTP, or SFTP server communicates with the device properly and the file path is set correctly on the server.
In the case of loading through FTP, TFTP, or SFTP, you can run the display progress load command to query the loading progress. In the case of loading through Xmodem, the display progress load command is unavailable.

During the loading process, the system displays the running information and related information, indicating the loading result, whether the loading is successful, and the failure cause if a failure occurs.

Prompt	Solution
Loading (backuping, rollbacking,duplicating) command being executed. Please retry later	Wait for the previous operation (loading, backup, duplication or rollback) to complete.
Failure: Load buffer is busy. Please retry later	Check whether an ongoing operation, such as loading, backup, or packet capturing, is being performed. Wait for the ongoing operation to complete or manually complete the operation.
Failure: Failed to transfer the file	Check whether the network is in the normal state. Check whether the IP address of the system and that of the file server are in the same network segment. Check whether the client is started. Check whether the current folder on the client is correct. Check whether the current folder on the client contains the file to be loaded.
Failure: CRC check of the loading file failure	Check whether the current file has been modified. Load the released file.
Failure: Error occurs when write flash	Check whether the hardware is faulty, rectify the fault, and reload the file.

After the file is loaded successfully, you can run the display xpon ont-interoperability-file command to query the information about the ONT interoperability file.

Example

To load the ONT interoperability file (stored in the server with IP address 10.10.10.10) through TFTP, do as follows:

huawei#load ont-interoperability-file
{ ftp<K>|sftp<K>|tftp<K>|xmodem<K> }:tftp                                  
{ ServerIpAddress<I><X.X.X.X> }:10.10.10.10                                
{ filename<S><Length 1-128> }:ont_iofile.iof                               
                                                                                
  Command:                                                                      
          load ont-interoperability-file tftp 10.10.10.10 ont_iofile.iof        
  Loading a new ONT interoperability file will overwrite the existing           
interoperability configurations on the OLT.                                     
  Are you sure you want to load this file?(y/n)[n]:y                       
  Load(backup,duplicate,...) begins, please wait and notice the rate of progress
  Any operation such as reboot or switchover will cause failure and             
unpredictable result                                                            
  The loading starts                                                            
  PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Load type: ONT               
interoperability file, Load Object: Active control board                        
                                                                                
huawei#                                                                
                                                                                
huawei#                                                                
  The loading is successful                                                     
  PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Load type: ONT               
interoperability file, Load Object: Active control board

Thanks

liqiang185 · Created Oct 14, 2019 06:55:19

Hello, please refer to the following two links, which are introduced in great detail.

https://forum.huawei.com/enterprise/en/is-it-necessary-to-have-an-interoperability-file-to-add-a-third-party-ont-to-the-olt/thread/559235-100181

https://forum.huawei.com/enterprise/en/how-to-add-3-rd-party-ont-to-huawei-olt-ma5608t/thread/486989-100181

ALISHAH · Created Apr 25, 2020 05:33:35

Hello, as I register third party ont in huawei olt and it works well at first time registeration, but If I delete same third party ont so it is not registering and pon light keep on blinking, but if I reboot huawei olt, than it work well, may I know what is the issue?

shahed · Created 3 days ago

I can solve 3rd-party ONT add with Huawei OLT with full functional. add me on skype if anyone need help.
My Skype: shahed.israr

registration third-party GPON ONT with huawei OLT GPON

Recommended answer

Usage Guidelines

Example

Third Party’s Trade Secret

My Followers

Enterprise

Consumer

Corporate

Carriers

registration third-party GPON ONT with huawei OLT GPON

Recommended answer

Usage Guidelines

Example

Third Party’s Trade Secret

My Followers