Rate Limit in Huawei 6720 & 5720 Switch

Created: Feb 12, 2020 04:51:13Latest reply: Feb 13, 2020 05:44:11 191 12 0 0
  Rewarded HiCoins: 0 (problem resolved)


i have two VLAN , creating Eth-tru1


vlan 500 -------  10Mbps download and upload

vlan 600 -------  20Mbps download and upload.


6720S ----- Vlan created 500 & 600  and connected to switch 5720

 

6720s----- Connected 5720  eth-truck 1.


5720  ----- ( port 5 and port 6) access port for vlan 500 and 600.


latop connected on port 5 & 6

 Port 5get 10Mbps up/down traffic if more than 10Mbps it should discard

 Port 6 get 20Mbps up/down traffic if more than 20Mbps it should discard



regards

singh.

  • x
  • convention:

Featured Answers
chenhui
Admin Created Feb 13, 2020 02:43:37 Helpful(0) Helpful(0)

Posted by Kundal at 2020-02-12 10:59 sorry lit correction , my eth interface is 10 & 11 outbound, my router/lan connected on port 2 ...
Hi @Kundal
does the traffic exceed the rate limitation continue for a long period , or just for a split second? Could it be caused by CBS?
  • x
  • convention:

Recommended answer

chenhui
Admin Created Feb 12, 2020 05:56:50 Helpful(1) Helpful(1)

Hi @Kundal

please refer the configuration below:

#############on S5720#################

int g0/0/5

 qos lr outbound cir 10240

 qos lr inbound cir 10240


int g0/0/6

 qos lr outbound cir 20480

 qos lr inbound cir 20480

#####################################


  • x
  • convention:

All Answers
chenhui
chenhui Admin Created Feb 12, 2020 05:56:50 Helpful(1) Helpful(1)

Hi @Kundal

please refer the configuration below:

#############on S5720#################

int g0/0/5

 qos lr outbound cir 10240

 qos lr inbound cir 10240


int g0/0/6

 qos lr outbound cir 20480

 qos lr inbound cir 20480

#####################################


  • x
  • convention:

Kundal
Kundal Created Feb 12, 2020 06:24:20 Helpful(0) Helpful(0)

Posted by chenhui at 2020-02-12 05:56 Hi @Kundalplease refer the configuration below:#############on S5720#################int g0/0/5 qos ...
yes, i have done this , but still traffic reaching uplink switch 1.2G on eth-trunk 6720s
  • x
  • convention:

chenhui
chenhui Admin Created Feb 12, 2020 07:06:33 Helpful(0) Helpful(0)

Posted by Kundal at 2020-02-12 06:24 yes, i have done this , but still traffic reaching uplink switch 1.2G on eth-trunk 6720s
Hi @Kundal
is there any other terminals connects to S5720? And would you please provide the interface configuration and the switch model and firmware version.
  • x
  • convention:

Kundal
Kundal Created Feb 12, 2020 08:50:16 Helpful(0) Helpful(0)

hi

6720 ------ port 1 & 2 connected with 5720 Port 1 & 2 as eth-trunk1 ... 5720 port 2 cisco router connected.

Huawei Versatile Routing Platform Software
VRP (R) software, Version 5.170 (S5720 V200R010C00SPC600)

--------------------------------------------------

i am suing this for 300Mbps
#
interface GigabitEthernet0/0/2
port link-type access
port default vlan 601
qos lr outbound cir 307200 cbs 38400000
qos lr inbound cir 307200 cbs 38400000

--------------------------------------

Interface PHY Protocol InUti OutUti inErrors outErrors
Eth-Trunk1 up up 2.82% 3.46% 9 0
GigabitEthernet0/0/10 up up 3.10% 0.50% 9 0
GigabitEthernet0/0/11 up up 2.53% 6.40% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0

----------------------------------------------------------------
  • x
  • convention:

chenhui
chenhui Admin Created Feb 12, 2020 09:37:01 Helpful(0) Helpful(0)

Posted by Kundal at 2020-02-12 08:50 hi 6720 ------ port 1 & 2 connected with 5720 Port 1 & 2 as eth-trunk1 ... 5720 port 2 cisco route ...
Hi @Kundal
from your configuration, the interface 1 and 2 are bound to eth-trunk 1, and you apply the configuration only on G0/0/2.
  • x
  • convention:

Kundal
Kundal Created Feb 12, 2020 10:59:08 Helpful(0) Helpful(0)

sorry lit correction , my eth interface is 10 & 11 outbound, my router/lan connected on port 2
  • x
  • convention:

LuizPuppin
LuizPuppin MVE Created Feb 12, 2020 14:19:14 Helpful(0) Helpful(0)

Only to add more info, you can use the control on VLAN too.
System view

traffic classifier vlan4000 operator and
if-match vlan-id 4000

traffic behavior vlan4000-Behavior
car cir 51200

Traffic policy vlan4000-Policy match-order config
classifier vlan4000-Banda behavior vlan4000-Behavior

interface Vlanif4000
traffic-policy vlan4000-Policy inbound
traffic-policy vlan4000-Policy outbound
  • x
  • convention:

I%20have%2020%20years%20working%20with%20telecom%20market.%20On%20all%20this%20time%20I%20worked%20always%20in%20great%20projects.%20The%20biggest%20was%20the%202014%20World%20Cup%20Command%20and%20Control%20Centre%2C%20where%20I%20was%20the%20Soluction%20Architect%20and%20Implementation%20Manager%20of%20Network%20and%20security%20Solution.%0AI%20work%20with%20Huawei%20s%20products%20to%20ISP%20Market%20since%202015%20and%20in%202017%20started%20to%20present%20trainnings%20customized%20to%20this%20market%2C%20focused%20in%20BGP%20and%20MPLS%20solution.%20I%20had%20more%20than%20400%20students%20and%20more%20than%20100%20ISP%20on%20my%20classes%20on%20last%2018%20mounths.
Saqib123
Saqib123 Created Feb 12, 2020 16:30:26 Helpful(0) Helpful(0)

hmmm
  • x
  • convention:

chenhui
chenhui Admin Created Feb 13, 2020 02:43:37 Helpful(0) Helpful(0)

Posted by Kundal at 2020-02-12 10:59 sorry lit correction , my eth interface is 10 & 11 outbound, my router/lan connected on port 2 ...
Hi @Kundal
does the traffic exceed the rate limitation continue for a long period , or just for a split second? Could it be caused by CBS?
  • x
  • convention:

12
Back to list

Comment

Reply
You need to log in to reply to the post Login | Register

Notice Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!

My Followers

Login and enjoy all the member benefits

Login and enjoy all the member benefits

Login