Got it
Huawei Enterprise Support Community
Community Forums Access Network
ONU P622E Config Intellig...

ONU P622E Config Intelligent Channel

Created: Apr 29, 2021 08:11:46Latest reply: Apr 29, 2021 08:28:39 362 3 0 0 0
  HiCoins as reward： 0 (problem unresolved)
View the author 1#

Hi, there.


I want to configure the Intelligent Channel on the ONU P622E, but I can't find where to configure the Intelligent Channel. Can you tell me the location? 

Thank you.

P622EIntelligent Channel

Like (0) Dislike (0) Favorite(0) Share Report
Previous: Modem için yazılım güncelleme dosyası...
Next: Xml
Featured Answers

Recommended answer

(0) (0)
Nino_Chou
Admin Created Apr 29, 2021 08:18:59

Hi, dear user.


To configure an intelligent channel, perform the following steps:

1. Click Advanced > Application tab, and choose Intelligent Channel in the navigation tree on the left. In the pane on the right, determine whether to enable the Intelligent Channel Enabled and configure related parameters,as shown in the following figure:


config


2. Click Apply.


Thanks.

View more
  • x
  • convention：

user_4046183
user_4046183 Created Apr 29, 2021 08:23:36 (0) (0)
Thank you, admin.
But I don't know the meaning of the parameter in the picture. Could you explain it to me again? Thank you very much.  
All Answers
(0) (0)
2#
Nino_Chou
Nino_Chou Admin Created Apr 29, 2021 08:18:59

Hi, dear user.


To configure an intelligent channel, perform the following steps:

1. Click Advanced > Application tab, and choose Intelligent Channel in the navigation tree on the left. In the pane on the right, determine whether to enable the Intelligent Channel Enabled and configure related parameters,as shown in the following figure:


config


2. Click Apply.


Thanks.

View more
  • x
  • convention：

user_4046183
user_4046183 Created Apr 29, 2021 08:23:36 (0) (0)
Thank you, admin.
But I don't know the meaning of the parameter in the picture. Could you explain it to me again? Thank you very much.  
(0) (0)
3#
Nino_Chou
Nino_Chou Admin Created Apr 29, 2021 08:28:39

Posted by Nino_Chou at 2021-04-29 08:18 Hi, dear user.To configure an intelligent channel, perform the following steps:1. Click Advanced  ...

It's okay, my friend.


The following table describes the intelligent channel parameters:

Parameter

Description

Intelligent Channel Enabled

Enables or disables the intelligent channel function.

Inbound Port

Indicates the port through which packets come in the ONT. The port must be the same as the LAN port that is bound to the WAN port of the intelligent channel service.

VLAN

Indicates the VLAN carried by packets when packets reach the inbound port. This parameter is not used for live-network services and thereby does not need to be configured.

Protocol No.

Indicates the Layer 3 protocol type of packets. Indicates the Layer 3 protocol type of packets. The following lists the numbers of common protocols:

  • TCP: 6

  • UDP: 17

  • IGMP: 2

  • ICMP: 1

Domain

Indicates the domain name of the intelligent channel. When both the destination IP address and the domain name are configured, the destination IP address takes precedence over the domain name (that is, the domain name does not take effect.)

The wildcard domain names in the following format are supported: *.abc.com, abc.com.*, and abc.*.com. The wildcard domain names in the following format are not supported: *abc.com, abc*.com, and a*c.com.

Destination IP Address/Mask

Indicates the destination IP address and mask of packets related to the intelligent channel service. The IP address can be an address or an address segment. Generally, only the destination IP address and mask need to be configured.

Source IP Address/Mask

Indicates the source IP address and mask of packets related to the intelligent channel service. The IP address can be an address or an address segment.

Destination Port Range

Indicates the destination TCP/IP port of packets. It can be a consecutive port range.

Source Port Range

Indicates the source TCP/IP port of packets. It can be a consecutive port range.

DSCP Re-marked

Indicates the DSCP value to be remarked. A greater DSCP value indicates a higher 802.1p priority.

802.1p Re-marked

Indicates the 802.1p value to be remarked, which is generated through association with the DSCP value. The 802.1p value is calculated based on the most significant 3 bits of the DSCP value.


Thanks.

View more
  • x
  • convention：
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.