Got it
Huawei Enterprise Support Community
Community Group Huawei Türkiye Teknik Forumu
Ne40e Access User Upload ...

Ne40e Access User Upload Speed

Created: Jan 7, 2022 07:36:51Latest reply: Jan 7, 2022 13:53:43 175 6 0 0 0
  HiCoins as reward： 0 (problem unresolved)
View the author 1#

Hi,


When Radius server assign to user 5 mbps upload, user speed test output is 8-10 mbps upload. If Radius assign to user 2 mbps upload , user speed test output 5-7 mbps. Why doesn't the router implement qos or why is there so many deviations? All users have the same problem.


ACL&QoS:

  Inbound qos configuration     : User-CAR

  Inbound cir                   : 5250(kbps)(Radius)

  Inbound pir                   : 5250(kbps)(Radius)

  Inbound cbs                   : 981750(bytes)

  Inbound pbs                   : 981750(bytes)

  Outbound qos configuration    : User-queue

  Outbound cir                  : 105000(kbps)(Radius)

  Outbound pir                  : 105000(kbps)(Radius)

  Link bandwidth auto adapt     : Disable

  UpPriority                    : Unchangeable

  DownPriority                  : Unchangeable


Device Version:

Huawei Versatile Routing Platform Software

VRP (R) software, Version 8.210 (NE40E V800R021C00SPC100)

Copyright (C) 2012-2021 Huawei Technologies Co., Ltd.

HUAWEI NE40E-X16A uptime is 18 days, 7 hours, 26 minutes 

Patch Version: V800R021HP0001





 


routerne40euploadNetwork Access Useraccess user

Like (0) Dislike (0) Favorite(0) Share Report
Previous: An interesting case of Network Redundancy with static Vxlan Tunnel
Next: Huawei FusionDirector installation and cluster configuration (E9000) section 0-installation
Featured Answers

Recommended answer

(0) (0)
fuzi_yao
Admin Created Jan 7, 2022 07:49:34

Hi, KorayK!

The NE40E supports QoS rate limiting. You can refer to the following configuration method.

Example for Configuring Traffic Policing

For your question, I think you should first check the RADIUS server because the device on which rate limiting is configured is not on the NE40E. Therefore, you should start to check the RADIUS server.


View more
  • x
  • convention：

KorayK.
KorayK. Created Jan 7, 2022 11:47:17 (0) (0)
Yes, the radius server sends the rate limit. But even though it sends by radius, the speed is 5250 inbound pir&cir on the router, I don't understand why the router doesn't apply it. Since I see this data in the router output, I don't think there is a problem in Radius.  
fuzi_yao
fuzi_yao Reply KorayK.  Created Jan 8, 2022 08:49:12 (0) (0)
friend!
To configure rate limiting on a router, you need to configure QoS rate limiting on the router so that the router can apply rate limiting. Otherwise, the router cannot perform rate limiting.  
All Answers
(0) (0)
2#
liqiang185
liqiang185 Admin Created Jan 7, 2022 07:43:17

Dear friend!
Please rest assured that we'll be back with an answer shortly.
View more
  • x
  • convention：
(0) (0)
3#
fuzi_yao
fuzi_yao Admin Created Jan 7, 2022 07:49:34

Hi, KorayK!

The NE40E supports QoS rate limiting. You can refer to the following configuration method.

Example for Configuring Traffic Policing

For your question, I think you should first check the RADIUS server because the device on which rate limiting is configured is not on the NE40E. Therefore, you should start to check the RADIUS server.


View more
  • x
  • convention：

KorayK.
KorayK. Created Jan 7, 2022 11:47:17 (0) (0)
Yes, the radius server sends the rate limit. But even though it sends by radius, the speed is 5250 inbound pir&cir on the router, I don't understand why the router doesn't apply it. Since I see this data in the router output, I don't think there is a problem in Radius.  
fuzi_yao
fuzi_yao Reply KorayK.  Created Jan 8, 2022 08:49:12 (0) (0)
friend!
To configure rate limiting on a router, you need to configure QoS rate limiting on the router so that the router can apply rate limiting. Otherwise, the router cannot perform rate limiting.  
(0) (0)
4#
KorayK.
KorayK. Created Jan 7, 2022 13:53:43

Executing the following command solved the problem.

[~Device] l2tp-group xx
[*Device-l2tp-xxx] qos scheduling-mode session
View more
  • x
  • convention：

fuzi_yao
fuzi_yao Created Jan 8, 2022 08:58:52 (0) (0)
This command is used for L2TP VPN scheduling. By default, tunnel scheduling is used. The limits the rate of the entire tunnel based on the user account. As a result, when multiple users share the same tunnel, the rate is also shared. As a result, the rate limiting problem occurs. Therefore, you have modified the scheduling mode to solve the problem.  
Back to list

Comment

You need to log in to comment to the post Login | Register

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.