Native vlan

Latest reply: Jan 23, 2014 08:44:58 7544 1 0 0

I am attempting to move the "Native" (Cisco Term), Untagged (Huawei Term) from VLAN 1 to VLAN 700.
I have a Trunk "TRK1" on the Huawei S5700 aggregating 8 Gig Interfaces together connectng to an EtherChannel on the Cisco WS-C3750X-48T-L which is also aggregating 8 Gig Interfaces together.  Everything was working fine when I first stood everything up using VLAN 1 as the Untagged / NATIVE Vlan.  (Yes, I know, why did you change it - another story).
I thought it would be very easy to change the NATIVE / Untagged VLAN but I am running into issues.
On the Cisco switch, I am receiving no events; but the Huawei , I am constantly receiving events.
Here is what I have configured on the Cisco Side....
interface Port-channel5
description CO22ZNBCRK1SW1
switcHuaweiort trunk encapsulation dot1q
switcHuaweiort trunk allowed vlan 1,5,300,500
switcHuaweiort mode trunk
switcHuaweiort nonegotiate
CO22DCWCRK1SW1#sho int port-channel 5 trunk
Port                Mode         Encapsulation  Status        Native vlan
Po5                 on           802.1q         trunking      1
Port                Vlans allowed on trunk
Po5                 1,5,300,500
Port                Vlans allowed and active in management domain
Po5                 1,5,300,500
Port                Vlans in spanning tree forwarding state and not pruned
Po5                 1,5,300,500
Per this output, I am using VLAN 1; however, the Huawei thinks differently.
Here are the events I am recieving on the Huawei Switch...
I 05/21/13 18:19:40 00828 lldp: PVID mismatch on port F20(VID 1)with peer device port Gi4/8(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F18(VID 1)with peer device port Gi4/7(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F16(VID 1)with peer device port Gi4/6(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F10(VID 1)with peer device port Gi4/3(VID 700)(363)
I 05/21/13 18:19:45 00828 lldp: PVID mismatch on port F12(VID 1)with peer device port Gi4/4(VID 700)(363)
I 05/21/13 18:19:52 00828 lldp: PVID mismatch on port F6(VID 1)with peer device port Gi4/1(VID 700)(362)
I 05/21/13 18:19:57 00828 lldp: PVID mismatch on port F14(VID 1)with peer device port Gi4/5(VID 700)(362)
I 05/21/13 18:19:58 00828 lldp: PVID mismatch on port F8(VID 1)with peer device port Gi4/2(VID 700)(362)
Here is configuration snippets from the Huawei 
trunk F6,F8,F10,F12,F14,F16,F18,F20 trk1 trunk
  Status : Port-based
  Voice : No
  Jumbo : No
  Port Information Mode     Unknown VLAN Status
  ---------------- -------- ------------ ----------
  Trk1             Untagged Learn        Up
I tried calling Huawei Technical Support and was told I must use VLAN 1 as the Untagged VLAN.  I don't believe this is true because I am using VLAN 700 between an Huawei 2700 and the same Huawei 5700 and have no issues.  The only difference is there are no aggregating ports.
I am thinking I either need to reboot the Huawei Switch or make the changes on the Huawei end (Far Side) moving to VLAN 700 as the Untagged VLAN, shutting down the port channel on the Cisco Side, make the change on the Cisco side and bring up the port channel.
Does anyone have other suggestions?
Thanks in advance...

  • x
  • convention:

Created Jan 23, 2014 08:44:58 Helpful(1) Helpful(1)

Hi there, 

If that alarm is not affecting the service, maybe you can try to get rid of it. 

You can do it in 2 ways:

1. disable lldp from interface view

[xxxxxx]interface gi0/0/1                                                                              
[xxxxxxxxx]undo lldp enable 

2. or you can use info-center filter-id command to filter the log from logbuffer

  • x
  • convention:


You need to log in to reply to the post Login | Register

Notice Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Login and enjoy all the member benefits

Login and enjoy all the member benefits