IPOE mac authentication with static ip adress

hello,

Did you use the following guide from documentation to accomplish the IPoE feature with mac authentication?
http://support.huawei.com/hedex/pages/EDOC110000652031189908/03/EDOC110000652031189908/03/resources/software/nev8r10_vrpv8r16/user/ne/dc_ne_ipox_cfg_0009.html?ft=0&fe=10&hib=7.17.6.7.7&id=dc_ne_ipox_cfg_0009&text=Example%20for%20Configuring%20MAC%20Authentication&docid=EDOC1100006520

It's best to share the NE40 configuration to understand what could be the problem.
Did you capture packets to check if accounting request is not coming?

from my understanding, accounting also should work for static ip address, I suggest you contact Huawei TAC, so that they can help you investigate further.

Pls refer the configuration


radius-server group xxxx
radius-server shared-key-cipher %^%#xFL;2CH:X-}$F(&^Z~!7PJEe)&+tA-xvT`Rr@AWX%^%#
radius-server authentication xxxx 1812 weight 0
radius-server accounting xxxx 1813 weight 0
radius-server type plus11
radius-server source interface GigabitEthernet5/0/0
radius-server attribute translate
undo radius-server user-name domain-included
radius-server traffic-unit kbyte
radius-attribute include HW-Auth-Type
radius-attribute translate extend HW-Auth-Type vendor-specific 2011 109 access-request account

ip pool mypool bas local
gateway 10.55.0.1 255.255.255.0
section 0 10.55.0.2 10.55.0.254
dns-server 4.2.2.2 8.8.8.8

aaa
default-user-name template test include mac-address :

domain ipoe
authentication-scheme ipoe
accounting-scheme postauth
radius-server group xxxx
ip-pool mypool
mac-authentication enable


interface GigabitEthernet5/0/1.508
user-vlan 508
bas
#
access-type layer2-subscriber default-domain authentication ipoe
authentication-method bind
ip-trigger
arp-trigger
default-user-name-template test

Radius debug
Aug 13 2018 19:22:42.565 xxxx-BNG %BRASRDS/7/BRRDS_DBG_PACKET(d):VS=Admin-VS-CID=0x8398041b;
Radius Sent a Packet
Server Template: 0
Server IP : xxxx
NAS IP : xxxx
Vpn-Instance: -
Server Port : 1812
NAS Port : 1812
Protocol: Portal
Code : Authentication request
Len : 277
ID : 226
[User-Name(1) ] [16] [0495:e64f:1078]
[User-Password(2) ] [18] [******]
[NAS-Port(5) ] [6 ] [83890684]
[NAS-IP-Address(4) ] [6 ] [xxxx]
[Service-Type(6) ] [6 ] [2] [Framed]
[Framed-Protocol(7) ] [6 ] [1] [PPP]
[Calling-Station-Id(31) ] [19] [04:95:e6:4f:10:78]
[NAS-Identifier(32) ] [12] [xxxx]
[NAS-Port-Type(61) ] [6 ] [15] [Ethernet]
[NAS-Port-Id(87) ] [37] [slot=5;subslot=0;port=1;vlanid=508;]



Aug 13 2018 19:22:42.565 xxxx-BNG %BRASRDS/7/BRRDS_DBG_PACKET(d):VS=Admin-VS-CID=0x8398041b;
[Acct-Session-Id(44) ] [35] [xxxx-05001050800000c2e071008700]
[Connect-Info(77) ] [12] [1000000000]
[HW-NAS-Startup-Time-Stamp(Huawei-59)] [6 ] [1531471198]
[HW-IP-Host-Address(Huawei-60) ] [35] [255.255.255.255 04:95:e6:4f:10:78]
[HW-Connect-ID(Huawei-26) ] [6 ] [34560]
[HW-Domain-Name(Huawei-138) ] [6 ] [ipoe]
[HW-User-Mac(Huawei-153) ] [19] [04:95:e6:4f:10:78]



Aug 13 2018 19:22:42.767 xxxx-BNG %BRASRDS/7/BRRDS_DBG_PACKET(d):VS=Admin-VS-CID=0x8398041b;
Radius Received a Packet
Server Template: 0
Server IP : xxxx
NAS IP : xxxx
Vpn-Instance: -
Server Port : 1812
NAS Port : 1812
Protocol: Portal
Code : Authentication accept
Len : 62
ID : 226
[Service-Type(6) ] [6 ] [2] [Framed]
[Session-Timeout(27) ] [6 ] [2678286]
[HW-Input-Committed-Information-Rate(Huawei-2)] [6 ] [52428800]
[HW-Output-Committed-Information-Rate(Huawei-5)] [6 ] [52428800]
[Framed-IP-Address(8) ] [6 ] [10.55.0.2]

Configuration seems correct from my perspective.
it's best to ask TAC for help. Check this link for contact:
http://e.huawei.com/en/service-hotline-query

The MAC address authentication configuration takes effect on an interface only after MAC address authentication is enabled globally and on the interface.

I suggest verify the RADIUS Server configuration, are you using an Agile Controller ? I suggest verify the NE supported by the RADIUS.

In the common issues the NE is not supported by the RADIUS .