Got it

Inter-Vlan communication upon a BAS interface

Created: Jul 17, 2019 17:37:44Latest reply: Jul 19, 2019 04:03:43 543 4 0 0 0
  Rewarded HiCoins: 0 (problem resolved)

Hello,


I have a NE 20 as a PPPoE AC connected to an OLT where my clients are physically connected through a ftth network. One of these clients would like to interconnect his two stores using vlans. I would like to know what is the best way to do that. I'm afraid to turn a l3 interface into a l2 and drop all PPPoE sessions


Best Regards

Featured Answers

Recommended answer

chenhui
Admin Created Jul 19, 2019 04:03:43

Posted by mrod at 2019-07-18 16:44 Hi Chenhui,Yes, that's it, he wants a layer2 connection. The Olt is connected using a Gigabit inte ...
I'll check it later, and I asked the Access engineers, they said that it's possible to build a layer 2 connection on the OLT, I'm not sure if this is helpful in this scenario.
View more
  • x
  • convention:

All Answers
Hi,

Huawei provides a variety of technologies to implement inter-VLAN communication. The following two technologies are commonly used:
  • VLANIF interface

    A VLANIF interface is a Layer 3 logical interface that can be used to implement inter-VLAN Layer 3 connectivity.

    It is simple to configure a VLANIF interface, so VLANIF interfaces are the most commonly used for inter-VLAN communication. However, a VLANIF interface needs to be configured for each VLAN and each VLANIF interface requires an IP address. As a result, this technology wastes IP addresses.

  • Dot1q termination sub-interface

    A sub-interface is also a Layer 3 logical interface that can be used to implement inter-VLAN Layer 3 connectivity.

    A Dot1q termination sub-interface applies to scenarios where a Layer 3 Ethernet interface connects to multiple VLANs. In such a scenario, data flows from different VLANs preempt bandwidth of the primary Ethernet interface; therefore, the primary Ethernet interface may become a bottleneck when the network is busy.

    For details about the Dot1q termination sub-interface, see VLAN Termination Configuration.

VLANIF interfaces require that users in VLANs be located on different network segments. (When hosts are located on the same network segment, a host encapsulates the destination host' MAC address in packets. The device determines that packets should be forwarded at Layer 2. Layer 2 switching is performed only in the same VLAN, and broadcast packets cannot reach different VLANs. In this case, the device cannot obtain destination hosts' MAC addresses and therefore cannot forward packets to the destination host.) On a network, VLAN aggregation can allow hosts on the same network segment in different VLANs to communicate.

VLAN aggregation, also known as super-VLAN, associates a super-VLAN with multiple sub-VLANs. The sub-VLANs share the IP address of the super-VLAN as the gateway IP address to implement Layer 3 connectivity with an external network. Proxy ARP can be enabled between sub-VLANs to implement Layer 3 connectivity between sub-VLANs. VLAN aggregation conserves IP addresses in inter-VLAN Layer 3 communication.

VLAN aggregation applies to scenarios where multiple VLANs share a gateway. For details about VLAN aggregation, see VLAN Aggregation Configuration.

For more details:

https://support.huawei.com/enterprise/my/doc/EDOC1000178168/90c96684/inter-vlan-communication


Thanks

View more
  • x
  • convention:

@mrod Hi,
Are you mind to provide a simple topology?
I'm not quite clear about your description.
Interconnect two stores using vlans, does this mean the customer want to built a layer 2 connection between the two stores?
How does the OLT connect to the NE20E?
View more
  • x
  • convention:

Posted by chenhui at 2019-07-18 01:48 @mrod Hi,Are you mind to provide a simple topology?I'm not quite clear about your description.Interc ...
Hi Chenhui,

Yes, that's it, he wants a layer2 connection. The Olt is connected using a Gigabit interface where I have some vlans to provide PPPoE access to customers.
View more
  • x
  • convention:

Posted by mrod at 2019-07-18 16:44 Hi Chenhui,Yes, that's it, he wants a layer2 connection. The Olt is connected using a Gigabit inte ...
I'll check it later, and I asked the Access engineers, they said that it's possible to build a layer 2 connection on the OLT, I'm not sure if this is helpful in this scenario.
View more
  • x
  • convention:

Comment

You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.