Huawei Enterprise Support Community

Community Forums Access Network

Huawei HG8145 ERROR: failed to select 'ubifs' partition, please format it first!

Created: Sep 3, 2021 00:24:44Latest reply: Sep 3, 2021 09:20:42 378 9 0 0 0

HiCoins as reward： 0 (problem unresolved)

I am getting this error via serial consol after failure firmware upgrade, please help me to solve this. T.I.A

HuaWei StartCode 2012.02 (V300R017C10 Sep 07 2017 - 11:54:40)

NAND:  Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
ECC Match pagesize:2K, oobzie:64, ecctype:4bit
Nand(Hardware): 256 MiB
startcode select the uboot to load
the high RAM is :8080103c
startcode uboot boot count:0
Use the UbootB to load first
Use the UbootB to load success


U-Boot 2010.03 (R16C10 Jul 14 2016 - 14:19:26)

DRAM:  256 MB
Boot From NAND flash
Chip Type is SD5116H
NAND:  Special Nand id table Version 1.23
Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
now using default nand flash type, Block:128KB Page:2KB!
ECC Match pagesize:2K, oobzie:64, ecctype:4bit
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bit
128 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
PHY power down !!!
[main.c__6080]::CRC:0x0, Magic1:0x0, Magic2:0x0, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
0x000000100000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI error: ubi_scan_get_free_peb: no eraseblocks found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
UBI init error -28
ERROR: failed to select 'ubifs' partition, please format it first!
Start from main system(0x0)!
CRC:0x0, Magic1:0x0, Magic2:0x0, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
0x000000100000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI error: ubi_scan_get_free_peb: no eraseblocks found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
UBI init error -28
ERROR: failed to select 'ubifs' partition, please format it first!
resetting ...

x
convention：
Emotion(0)

Like (0) Dislike (0) Favorite(0) Report

 Previous: WA8021V5 - Doubt

Next: HG8145V5 USB PORT HAS NO CONFIGURATION FOR FTP



Featured Answers

Recommended answer

(0) (0)

from 3#

Chenxintao Admin Created Sep 3, 2021 02:34:48

Hello friend!

According to the information you provided, the flash data of the device is damaged.

Because the flash data cannot be repaired, you need to replace the device.

Thanks!

x
convention：

PanchakS Created Sep 3, 2021 03:59:41 (0) (0)

user_4367907 Created Sep 3, 2021 12:21:11 (0) (0)
Are you sure dear that flash data of the device cannot be repair if damaged?

Chenxintao Reply user_4367907 Created Sep 3, 2021 12:27:48 (0) (0)
Hi, my friend!
Yes, flash data corruption indicates that the hardware of the device is damaged and cannot be repaired.

user_4367907 Reply Chenxintao Created Sep 3, 2021 12:35:11 (0) (0)
I believe any type of software issue can be fixed including nand flash data, just need to know the way, I have flash also TP-Link flash by removing from the board also I strongly believe nand data can be copied from another device.

user_4367907 Reply Chenxintao Created Sep 3, 2021 13:19:46 (0) (0)
Check this link bro
https://www.right.com.cn/FORUM/thread-769297-1-1.html

All Answers

(0) (0)

^2#

stephen.xu Admin Created Sep 3, 2021 00:25:24

Hi, dear

Please kindly wait for a minute.

x
convention：

(0) (0)

^3#

Chenxintao Admin Created Sep 3, 2021 02:34:48

Hello friend!

According to the information you provided, the flash data of the device is damaged.

Because the flash data cannot be repaired, you need to replace the device.

Thanks!

x
convention：

PanchakS Created Sep 3, 2021 03:59:41 (0) (0)

user_4367907 Created Sep 3, 2021 12:21:11 (0) (0)
Are you sure dear that flash data of the device cannot be repair if damaged?

Chenxintao Reply user_4367907 Created Sep 3, 2021 12:27:48 (0) (0)
Hi, my friend!
Yes, flash data corruption indicates that the hardware of the device is damaged and cannot be repaired.

user_4367907 Reply Chenxintao Created Sep 3, 2021 13:19:46 (0) (0)
Check this link bro
https://www.right.com.cn/FORUM/thread-769297-1-1.html

(0) (0)

^4#

PanchakS

Created Sep 3, 2021 03:59:48

Good answer

x
convention：

(0) (0)

^5#

Unicef

MVE Created Sep 3, 2021 09:20:42

Nice

x
convention：

Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:

Politically sensitive content
Content concerning pornography, gambling, and drug abuse
Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy

Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

Huawei HG8145 ERROR: failed to select 'ubifs' partition, please format it first!

Recommended answer

Third Party’s Trade Secret

`@trans`bright_future`~trans`

My Followers

Enterprise

Consumer

Corporate

Carriers

Huawei HG8145 ERROR: failed to select 'ubifs' partition, please format it first!

Recommended answer

Third Party’s Trade Secret

`@trans`bright_future`~trans`

My Followers