30 27012050 Vehicle-Mounted 5 GHz Dual-Polarized Directional Antenna (H70 V35 G9)
30.1 Technical Parameters
The 27012050 directional antenna is applicable to wireless coverage on vehicles.
Antenna Appearance
Technical Specifications
Table 30-1 lists technical specifications of the 27012050 antenna.
|
Item |
Value |
|---|---|
|
Frequency (MHz) |
5150-5850 |
|
Gain (dBi) |
9 |
|
Horizontal lobe width (degree) |
70 |
|
Vertical lobe width (degree) |
35 |
|
Standing wave ratio (SWR) |
≤ 2 |
|
Polarization |
Horizontal, vertical, and cross polarization |
|
Connector |
3 x QMA-male |
|
Dimensions (mm) |
Diameter x Length: φ110 x 33 |
|
Weight (g) |
240 |
|
Mounting mode |
Wall mounting |
|
Applicable AP |
AP9132DN |
NOTE:
- The gains and lobe widths in this document are typical values. The actual values are within a range. For specifications, see the corresponding data sheets.
-
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with local standards. For details, refer to device access authentication information.
30.2 Safety Precautions
30.2.1 General Safety Precautions
This section describes safety precautions that instruct you to select measuring and testing instruments when you install, operate, and maintain Huawei equipment.
All Safety Precautions
To ensure human safety and equipment safety, comply with all the safety precautions marked on the equipment and instructed in this document.
WARNING, CAUTION, and DANGER items in this document do not cover all the safety cautions and are only supplementary to the safety cautions.
Local Laws and Regulations
When operating a device, abide by local laws and regulations. The safety precautions instructed in the document are supplementary to the local laws and regulations.
Basic Installation Requirements
Only trained and qualified personnel are allowed to install or maintain Huawei equipment. Familiarize yourself with all safety precautions before performing any operation on the equipment.
- Only the trained and qualified personnel are permitted to install, operate, and maintain Huawei equipment.
- Only the qualified personnel are permitted to dismantle safety appliances and repair Huawei equipment.
- Only the personnel certified or authorized by Huawei are permitted to replace or change Huawei equipment or parts of Huawei equipment (including software).
- The operating personnel must immediately report the faults or errors that may cause safety problems to the person in charge.
Grounding Requirements
Equipment that needs to be grounded must meet the following requirements:
- When installing the equipment, ground the equipment before any operations and remove the ground cable only after you remove all the other components and cables from the equipment.
- Ensure that the ground conductor is intact.
- Do not operate the equipment in the absence of a suitably installed ground conductor.
- The equipment must be connected to the PGND permanently. Before operating the equipment, check the electrical connections of the equipment and ensure that the equipment is properly grounded.
Personal Safety
- Do not operate the equipment and cables in a thunderstorm.
- To avoid electric shocks, do not connect safety extra-low voltage (SELV) circuits to telecommunication network voltage (TNV) circuits.
- Invisible laser beams will cause eye damage. Do not look into bores of optical modules or connectors of optical fibers without eye protection.
- Before performing any operation on the equipment, wear ESD clothing and ESD gloves or an ESD wrist strap. Remove conductive objects like jewelry and watches to avoid electric shock or burn.
- In case of fire, immediately leave the building or equipment deployment site and press the fire alarm button or call the fire department. Never enter the building on fire again in any situation.
Equipment Safety
- Before any operation, install the equipment firmly on the ground or other rigid objects, such as on a wall or in a rack.
- When the system is working, ensure that the ventilation hole is not blocked.
- When installing panels, use necessary tools to fasten the screws.
- After equipment installation is complete, clean up the packing materials.
30.2.2 Electrical Safety Precautions
This section describes safety precautions for high voltage, thunderstorms, high leakage current, power cables, and fuses.
High Voltage
DANGER:
- Direct contact with a high-voltage power source or indirect contact through damp objects can be fatal.
- Misoperations on high-voltage facilities may result in fire, electric shock, or other accidents.
High Leakage Current
CAUTION:
If a high leakage current mark is labeled near the power connector of the equipment, you must connect the PGND terminal on the shell to the ground before connecting the equipment to an AC input power supply. This is to prevent the electric shock caused by leakage current of the equipment.
Power Cable
DANGER:
- Before installing or removing power cables, you must power off the equipment.
- Before connecting a power cable, verify that the label on the power cable is correct.
Fuses
CAUTION:
30.2.3 Working at Heights
This section describes safety precautions you need to take when working at heights.
CAUTION:
The requirements for working at heights are as follows:
- The personnel who work at heights must be trained.
- Carry and handle the operating machines and tools with caution to prevent them from falling down.
30.3 Antenna Installation
The 27012050 antenna is a vehicle-mounted directional antenna and applicable to wireless coverage on vehicles.
30.3.1 Accessories and Tools
The following accessories and tools are required for installing the 27012050 antenna.
- One screwdriver
- Three M4 screws
30.3.2 Wall Mounting
The 27012050 antenna can be mounted on a wall in a vehicle.
NOTE:
- Determine the antenna mounting method according to onsite situations.
- Select the proper outlet direction for the feeder, preventing small-angle bending of the feeder.
- Select a suitable mounting position on the inner wall of a vehicle based on the positions and dimensions of mounting holes of the antenna, as shown in the following figure (unit: mm).
- Fix the antenna on the inner wall of the vehicle using three screws.
30.3.3 Connecting RF Cables
RF Cable Connection
Connect three feeder ports A, B, and C of the antenna to radio interfaces A, B, and C of the corresponding frequency bands on the AP.
RF Cable Deployment Requirements
- Use a short feeder cable to connect the antenna to an AP.
- It is recommended that you connect a 50 ohm RF load to an idle antenna interface.
- Bend radius requirements: RG-8U RF cable: > 150 mm; 1/2" RF cable:> 50 mm; 7/8" RF cable: > 250 mm. One inch (1") equals 25.4 mm.
