3 27010209 Indoor 2.4 GHz Single-Polarized Directional Antenna (H88 V47 G7)
3.1 Technical Parameters
27010209 directional antennas are applicable in indoor scenarios.
Antenna Appearance
Technical Specifications
Table 3-1 lists technical specifications of the 27010209 antenna.
|
Item |
Value |
|---|---|
|
Frequency (MHz) |
1710–2500 |
|
Gain (dBi) |
7 |
|
Horizontal lobe width (degrees) |
88 |
|
Vertical lobe width (degrees) |
47 |
|
Standing wave ratio (SWR) |
≤ 1.5 |
|
Polarization |
Vertical polarization |
|
Connector |
N-female |
|
Dimensions (mm) |
H x W x D: 210 x 180 x 44 |
|
Weight (g) |
430 |
|
Mounting mode |
Wall mounting |
|
Applicable AP |
AP6310SN |
NOTE:
- The gains and lobe widths in this document are typical values. The actual values are within a range. For specifications, see the corresponding data sheets.
-
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with local standards. For details, refer to device access authentication information.
Antenna Pattern
3.2 Safety Precautions
3.2.1 General Safety Precautions
This section describes safety precautions that instruct you to select measuring and testing instruments when you install, operate, and maintain Huawei equipment.
All Safety Precautions
To ensure human safety and equipment safety, comply with all the safety precautions marked on the equipment and instructed in this document.
WARNING, CAUTION, and DANGER items in this document do not cover all the safety cautions and are only supplementary to the safety cautions.
Local Laws and Regulations
When operating a device, abide by local laws and regulations. The safety precautions instructed in the document are supplementary to the local laws and regulations.
Basic Installation Requirements
Only trained and qualified personnel are allowed to install or maintain Huawei equipment. Familiarize yourself with all safety precautions before performing any operation on the equipment.
- Only the trained and qualified personnel are permitted to install, operate, and maintain Huawei equipment.
- Only the qualified personnel are permitted to dismantle safety appliances and repair Huawei equipment.
- Only the personnel certified or authorized by Huawei are permitted to replace or change Huawei equipment or parts of Huawei equipment (including software).
- The operating personnel must immediately report the faults or errors that may cause safety problems to the person in charge.
Grounding Requirements
Equipment that needs to be grounded must meet the following requirements:
- When installing the equipment, ground the equipment before any operations and remove the ground cable only after you remove all the other components and cables from the equipment.
- Ensure that the ground conductor is intact.
- Do not operate the equipment in the absence of a suitably installed ground conductor.
- The equipment must be connected to the PGND permanently. Before operating the equipment, check the electrical connections of the equipment and ensure that the equipment is properly grounded.
Personal Safety
- Do not operate the equipment and cables in a thunderstorm.
- To avoid electric shocks, do not connect safety extra-low voltage (SELV) circuits to telecommunication network voltage (TNV) circuits.
- Invisible laser beams will cause eye damage. Do not look into bores of optical modules or connectors of optical fibers without eye protection.
- Before performing any operation on the equipment, wear ESD clothing and ESD gloves or an ESD wrist strap. Remove conductive objects like jewelry and watches to avoid electric shock or burn.
- In case of fire, immediately leave the building or equipment deployment site and press the fire alarm button or call the fire department. Never enter the building on fire again in any situation.
Equipment Safety
- Before any operation, install the equipment firmly on the ground or other rigid objects, such as on a wall or in a rack.
- When the system is working, ensure that the ventilation hole is not blocked.
- When installing panels, use necessary tools to fasten the screws.
- After equipment installation is complete, clean up the packing materials.
3.2.2 Electrical Safety Precautions
This section describes safety precautions for high voltage, thunderstorms, high leakage current, power cables, and fuses.
High Voltage
DANGER:
- Direct contact with a high-voltage power source or indirect contact through damp objects can be fatal.
- Misoperations on high-voltage facilities may result in fire, electric shock, or other accidents.
High Leakage Current
CAUTION:
If a high leakage current mark is labeled near the power connector of the equipment, you must connect the PGND terminal on the shell to the ground before connecting the equipment to an AC input power supply. This is to prevent the electric shock caused by leakage current of the equipment.
Power Cable
DANGER:
- Before installing or removing power cables, you must power off the equipment.
- Before connecting a power cable, verify that the label on the power cable is correct.
Fuses
CAUTION:
3.2.3 Working at Heights
This section describes safety precautions you need to take when working at heights.
CAUTION:
The requirements for working at heights are as follows:
- The personnel who work at heights must be trained.
- Carry and handle the operating machines and tools with caution to prevent them from falling down.
3.3 Antenna Installation
The 27010209 antenna is an indoor directional antenna. It forms a major lobe in a certain direction with high gains, while other directions have low gains. It applies to scenarios that require small coverage angles but long coverage distances. Typical scenarios include corridors in hospitals or airports.
3.3.1 Accessories and Tools
- Hammer drill (φ6 mm, for wall mounting)
- Rubber mallet (for wall mounting)
- Mounting bracket: 1 set
- M4 expansion bolt: 4 sets
3.3.2 Wall Mounting
The 27010209 antenna can be mounted on a wall.
- Drill four φ6 mm holes (35 mm depth) on the wall to install plastic expansion tubes that will support expansion bolts. The relative position of the four holes must exactly match with that of the four holes on the antenna mounting bracket.
- Fix the antenna support to the wall using expansion bolts.
- Insert the clamp mounting part on the bottom plate of the antenna to the hook on the mounting bracket.
3.3.3 Connecting RF Cables
RF Cable Deployment Requirements
- Use a short feeder cable to connect the antenna to an AP.
- It is recommended that you connect a 50 ohm RF load to an idle antenna interface.
- Bend radius requirements: RG-8U RF cable: > 150 mm; 1/2" RF cable:> 50 mm; 7/8" RF cable: > 250 mm. One inch (1") equals 25.4 mm.
Instructions on Making RF Cables
Connecting the type-N male coaxial connector to the RG-8U feeder cable
- Peel the cable.
- Install accessories, such as the nut.
- Install the connector body.
- Tighten the connector on the cable.
Connecting the type-N male coaxial connector to the 1/2" feeder cable
- Peel the cable.
- Install the back nut.
- Install the front nut.
- Put the cable through the heat-shrink tubing.
