Got it
Huawei Enterprise Support Community
Community Forums Intelligent Video Surveillance
How to reset the PTZ cont...

How to reset the PTZ control of the PTZ dome camera?

Created: Jul 24, 2019 11:21:46Latest reply: Jul 24, 2019 11:40:15 1119 1 0 0 0
  Rewarded HiCoins： 0 (problem resolved)
View the author 1#

Hi!


This post enquires how to reset the PTZ control of the PTZ dome camera.


I have a PTZ dome camera IPC 6525-Z30 and its PTZ controls are inverted.


Please help me to reset them.


Thanks!



Like (0) Dislike (0) Favorite(0) Share Report
Previous: How to unlimit the number of tries for entering wrong password
Next: How to configure secondary stream
Featured Answers

Best answer

Recommended answer

(0) (0)
Hike
Created Jul 24, 2019 11:40:15

Hi, enaya!

Please refer to the following information.

Setting PTZ Channel Parameters (Externally Connecting to a PTZ Device)

Procedure

1. When an IPC is connected to a PTZ device, you need to set the PTZ channel parameters, as shown in Figure 2. Table 1 describes the parameters.  
 
Before setting the PTZ parameters on the web pages, ensure that the PTZ has been connected to the camera and the related PTZ configurations have been completed.
 
Figure 2. Setting PTZ parameters
How to reset the PTZ control of the PTZ dome camera?-3010923-1

NOTE:
 
Ensure that the values of the web PTZ parameters are the same as those of the external PTZ parameters. Otherwise, the external PTZ cannot be used properly.

Table 1. PTZ parameters
[tr]Parameter
Description
[/tr]
PTZ ID
Indicates the unique ID of the PTZ.
Enable
Indicates whether to enable the serial port.
Serial port ID
Indicates the PTZ serial port ID.
PTZ protocol
Indicates the PTZ protocol type.
PTZ address
Indicates the PTZ address.
Direction control
Used to perform forward or backward control of the PTZ.
  • Forward: Enables the forward control of the PTZ. For example, if you click the left button, the PTZ moves leftward.
  • Backward: Enables the backward control of the PTZ. For example, if you click the left button, the PTZ moves rightward.
Wiper linkage switch output 1
Indicates whether to enable the wiper linkage switch output 1. Select the check box to enable it.
NOTE:

  • To use the rain wiper that is controlled by the Boolean value, connect the rain wiper to Boolean value output 1 and enable the rain wiper.
  • If Boolean value output 1 connects to an alarm device, do not enable the function.
  • If the function is not enabled, the rain wiper button in the PTZ control is unavailable. 
View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
All Answers
(0) (0)
2#
Hike
Hike Created Jul 24, 2019 11:40:15

Hi, enaya!

Please refer to the following information.

Setting PTZ Channel Parameters (Externally Connecting to a PTZ Device)

Procedure

1. When an IPC is connected to a PTZ device, you need to set the PTZ channel parameters, as shown in Figure 2. Table 1 describes the parameters.  
 
Before setting the PTZ parameters on the web pages, ensure that the PTZ has been connected to the camera and the related PTZ configurations have been completed.
 
Figure 2. Setting PTZ parameters
How to reset the PTZ control of the PTZ dome camera?-3010923-1

NOTE:
 
Ensure that the values of the web PTZ parameters are the same as those of the external PTZ parameters. Otherwise, the external PTZ cannot be used properly.

Table 1. PTZ parameters
[tr]Parameter
Description
[/tr]
PTZ ID
Indicates the unique ID of the PTZ.
Enable
Indicates whether to enable the serial port.
Serial port ID
Indicates the PTZ serial port ID.
PTZ protocol
Indicates the PTZ protocol type.
PTZ address
Indicates the PTZ address.
Direction control
Used to perform forward or backward control of the PTZ.
  • Forward: Enables the forward control of the PTZ. For example, if you click the left button, the PTZ moves leftward.
  • Backward: Enables the backward control of the PTZ. For example, if you click the left button, the PTZ moves rightward.
Wiper linkage switch output 1
Indicates whether to enable the wiper linkage switch output 1. Select the check box to enable it.
NOTE:

  • To use the rain wiper that is controlled by the Boolean value, connect the rain wiper to Boolean value output 1 and enable the rain wiper.
  • If Boolean value output 1 connects to an alarm device, do not enable the function.
  • If the function is not enabled, the rain wiper button in the PTZ control is unavailable. 
View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.