How to query the stack configuration on S series switches

Created: May 28, 2019 11:46:04Latest reply: May 28, 2019 11:46:56 64 1 0 0
  Rewarded Hi-coins: 0 (problem resolved)

How to query the stack configuration on S series switches

  • x
  • convention:

Featured Answers
All_About_Switch
Official Created May 28, 2019 11:46:56 Helpful(0) Helpful(0)

Hi there!

In the case of S series switches, the stack configuration is not recorded in the configuration file. Therefore, you cannot view the stack configuration by running the display current-configuration command.

Run the display stack command to view information about the stack system. 

[HUAWEI] display stack
Stack mode: Service-port                                                      
Stack topology type: Link                                                      
Stack system MAC: 0000-1382-4569                                                
MAC switch delay time: 10 min                                                   
Stack reserved VLAN: 4093                                                      
Slot of the active management port: 0
Slot    Role        MAC address       Priority   Device type
-------------------------------------------------------------
    0   Master      0018-82b1-6eb4   200          S5700-28P-LI-AC
    1   Standby     0018-82b1-6eba   150          S5700-28P-LI-AC
# Run the display stack configuration or display stack current-configuration command to view the stack configuration. The following uses V200R012C00 as an example.
[HUAWEI]display stack configuration
*    : Invalid-configuration   
#    : Unsaved configuration
---------------Configuration on slot 1 Begin---------------
stack enable                       
stack slot 0 renumber 2            
stack slot 2 priority 150            
stack reserved-vlan 4093              
stack timer mac-address switch-delay 10                                                                                          
interface stack-port 1/1            
*port interface XGigabitEthernet1/0/1 enable
interface stack-port 1/2            
#port interface XGigabitEthernet1/0/4 enable
---------------Configuration on slot 1 End----------------- 
 
# Run the display stack port command to view the stack interface configuration. The following uses V200R012C00 as an example.
[HUAWEI] display stack port
*down : administratively down      
(r)   : Runts trigger error down   
(c)   : CRC trigger error down      
(l)   : Link-flapping trigger error down
(m)   : Media mismatch trigger error down
Logic Port         Phy Port                     Online       Status
----------------------------------------------------------------------------
stack-port0/1      XGigabitEthernet0/0/1        present      down
  • x
  • convention:

All Answers
All_About_Switch
All_About_Switch Official Created May 28, 2019 11:46:56 Helpful(0) Helpful(0)

Hi there!

In the case of S series switches, the stack configuration is not recorded in the configuration file. Therefore, you cannot view the stack configuration by running the display current-configuration command.

Run the display stack command to view information about the stack system. 

[HUAWEI] display stack
Stack mode: Service-port                                                      
Stack topology type: Link                                                      
Stack system MAC: 0000-1382-4569                                                
MAC switch delay time: 10 min                                                   
Stack reserved VLAN: 4093                                                      
Slot of the active management port: 0
Slot    Role        MAC address       Priority   Device type
-------------------------------------------------------------
    0   Master      0018-82b1-6eb4   200          S5700-28P-LI-AC
    1   Standby     0018-82b1-6eba   150          S5700-28P-LI-AC
# Run the display stack configuration or display stack current-configuration command to view the stack configuration. The following uses V200R012C00 as an example.
[HUAWEI]display stack configuration
*    : Invalid-configuration   
#    : Unsaved configuration
---------------Configuration on slot 1 Begin---------------
stack enable                       
stack slot 0 renumber 2            
stack slot 2 priority 150            
stack reserved-vlan 4093              
stack timer mac-address switch-delay 10                                                                                          
interface stack-port 1/1            
*port interface XGigabitEthernet1/0/1 enable
interface stack-port 1/2            
#port interface XGigabitEthernet1/0/4 enable
---------------Configuration on slot 1 End----------------- 
 
# Run the display stack port command to view the stack interface configuration. The following uses V200R012C00 as an example.
[HUAWEI] display stack port
*down : administratively down      
(r)   : Runts trigger error down   
(c)   : CRC trigger error down      
(l)   : Link-flapping trigger error down
(m)   : Media mismatch trigger error down
Logic Port         Phy Port                     Online       Status
----------------------------------------------------------------------------
stack-port0/1      XGigabitEthernet0/0/1        present      down
  • x
  • convention:

Reply

Reply
You need to log in to reply to the post Login | Register

Notice Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Login and enjoy all the member benefits

Login and enjoy all the member benefits

Login