Got it

How to enable Traffic-Policy and Flow control on Quidway S2700-26TP-SI-AC

Latest reply: Apr 22, 2020 01:25:25 2866 4 0 0

Hi Dear,

I am trying to configure Traffic policy and want to enable flow control on my "Quidway S2700-26TP-SI-AC" switch but I do not see any command to do so. Firmware on Switch is "Software Version V100R006C05"

are Traffic Policy and flow control not supported on this switch or some patch is needed to support the same.

Request you to please provide your inputs.

Thanks & Regards,


  • x
  • convention:

Created Nov 13, 2014 08:25:43 Helpful(0) Helpful(0)

"Quidway S2700-26TP-SI-AC" doesn't support traffic policy.

Use two command to enable flow control:

interface interface-type interface-number


View more
  • x
  • convention:

Created Nov 13, 2014 09:33:26 Helpful(0) Helpful(0)

I alreadt tried first command and after that flow command but it says command not recongnized. Have a look at the list of commands supported for a interface below:

[HW_GREEN]interface Ethernet 0/0/1
ethernet-l2 interface view commands:
  als                    Set automatic laser shutdown
  am                     Port isolate
  auto                   Auto negotiates port mode
  broadcast-suppression  Set broadcast flow suppression
  carrier                Set carrier function
  description            Specify interface description
  display                Display current system information
  duplex                 Configure duplex operation mode
  enable                 Enable function
  error-statistics       Error-statistics
  eth-trunk              Add the interface into eth-trunk
  igmp-snooping          Specify parameters for IGMP-Snooping
  l2-multicast           Specify parameters for Layer 2 multicast
  lldp                   Link Layer Discovery Protocol
  log-threshold          Set log threshold
  loopback               Configure port loopback
  loopback-detect        Loopback detect function
  loopbacktest           Configure port loopback test
  mac-address            MAC address
  mac-limit              MAC limit
  mdi                    Set mdi
  mirror-reserve-port    Specify mirror-reserve-port
  multicast-suppression  Set multicast flow suppression
  negotiation            Set negotiation mode
  ping                   Send echo messages
  port                   Switch port
  port-auto-sleep        port auto-power-down function
  port-isolate           Port isolate
  port-mirroring         Mirror port
  qos                    QoS configuration
  quit                   Exit from current command view
  reset                  Reset
  restart                Restart the specified interface
  return                 Exit to user view
  rmon                   Specify RMON configuration
  rmon-statistics        Specify RMON statistics
  screen-width           Set screen width
  set                    Set the phy status of the interface
  shutdown               Shutdown the specified interface
  speed                  Configure port speed mode
  stp                    Specify Spanning Tree Protocol (STP) configuration
  test-aaa               Accounts test
  tracert                Trace route to host
  transceiver            Transceiver
  trap-threshold         Set trap threshold
  trust                  Specify trust parameters
  undo                   Cancel the setting
  virtual-cable-test     Virtual Cable Test


You can clearly see here flow-control command is not there. Same is the case with Traffic-Policy as well.

View more
  • x
  • convention:

Created Apr 22, 2020 01:25:16 Helpful(0) Helpful(0)

Very pleased with the information you shared!
View more
  • x
  • convention:

Created Apr 22, 2020 01:25:25 Helpful(0) Helpful(0)

Nice job, thank you!
View more
  • x
  • convention:


You need to log in to comment to the post Login | Register

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."

My Followers

Login and enjoy all the member benefits


Huawei Enterprise Support Community
Huawei Enterprise Support Community
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Please bind your phone number to obtain invitation bonus.