How can I change the idle time for the BMU web page

Hey,girl · Created Oct 28, 2019 02:19:44

Posted by Nasr at 2019-10-27 09:55 okay but the customer, need to change it.

hello, you can change parameter of the web.xml

/opt/eSpace_UC/eSpace_UC_Server/Server/BMU/webapps/portal/WEB-INFO/web.xml
(this link is a Linux environment, if your environment is windows, you can find the web.xml file at installation directory)

the parameter is session-timeout

Please notice

Files may be overwritten after upgrade

Jacob2 · Created Oct 27, 2019 08:27:29

The default time is the tested time, which can effectively protect the environment safety, it is not recommended to modify

Nasr · Created Oct 27, 2019 09:55:14

okay but the customer, need to change it.

wissal · Created Oct 27, 2019 10:42:09

Hello,

Please find below how to change the idle time for the BMU web page :

Configuring the BMU

To allow users to view CDRs on the BMU, configure the CDRServer on the BMU side.

The BMU can obtain CDRs from the directory where CDRs are stored on the CDRServer through an FTP or FTPS interface. The default directory is D:\Bill\CurFile.

Log in to the BMU as the admin user.
Choose Functions Maintenance > CDR Configuration.
The CDR Configuration page is displayed.
Configure CDR information, as shown in Figure 1.
Figure 1 CDR Settings
Set the following parameters:
- CDRServer IP Address: Indicates the CDRServer IP address.
- Port: Indicates the FTP or FTPS service port, which must be the same as the setting on the FTP/FTPS Server.
- FTP User Name: Indicates the FTP user name for obtainin****Rs. The user name is configured during the FTP or FTPS Server installation.
- FTP Password: FTP user name for CDRs. The user name is configured during the FTP or FTPS Server installation.
- FTP: It is recommended that you use the FTPS protocol. Using FTP to transfer files may bring some security risks because FTP is an insecure protocol.
- The interval for obtainin****Rs must meet the following requirements:
  - In V200R002C00SPC206 or an earlier version, the recommended value does not exceed the link timeout value (default: 5 min) of the FTPServer. Cause: A reconnection mechanism does not exist between the BMU and FTPServer. When the FTP Server is disconnected, CDRs cannot be obtained.
  - In V200R003C00 or a later version, a reconnection mechanism exists between the BMU and FTPServer, and the interval value is not restricted.
Click Connect.
Click OK.

For more details

http://support.huawei.com/hedex/hdx.do?lib=EDOC1000073292DEE0403M&docid=EDOC1000073292&lang=en&v=23&tocLib=EDOC1000073292DEE0403M&tocV=23&id=ipt_cmsg_00208&tocURL=resources%2fcmsg%5fu1900%2fipt%5fcmsg%5f00208%2ehtml&p=t&fe=1&ui=3&keyword=BMU

Thanks

Hey,girl · Created Oct 28, 2019 02:19:44

Posted by Nasr at 2019-10-27 09:55 okay but the customer, need to change it.

hello, you can change parameter of the web.xml

/opt/eSpace_UC/eSpace_UC_Server/Server/BMU/webapps/portal/WEB-INFO/web.xml
(this link is a Linux environment, if your environment is windows, you can find the web.xml file at installation directory)

the parameter is session-timeout

Please notice

Files may be overwritten after upgrade

How can I change the idle time for the BMU web page

Best answer

Configuring the BMU

Third Party’s Trade Secret

`@trans`bright_future`~trans`

`@trans`drinking_poetry`~trans`

My Followers

Enterprise

Consumer

Corporate

Carriers

How can I change the idle time for the BMU web page

Best answer

Configuring the BMU

Third Party’s Trade Secret

`@trans`bright_future`~trans`

`@trans`drinking_poetry`~trans`

My Followers