H835ADLE Not Showing Ports; SmartAX MA5616

liqiang185 · Created Feb 16, 2020 10:38:22

Dear Seeking66!

You need to enter this command：board confirm { frameid | frameid/slotid }

Thank you！

liqiang185 · Created Feb 16, 2020 10:38:22

Dear Seeking66!

You need to enter this command：board confirm { frameid | frameid/slotid }

Thank you！

wissal · Created Feb 16, 2020 10:40:59

Hello,

Please find below the answer for your issue:

display board

Function

This command is used to query the information about boards of a shelf or a specified board. To query the slot ID, name, state, port information, or online/offline state of a board, run this command.

NOTE:

The software operations supported by this function is depended on hardware. Specifically, commands can be issued only if they are supported by the hardware.
The valid value of the frameid parameter involved in all MA5616 products is 0.

Format

display board frameid [ /slotid ]

Parameters

Parameter	Description	Value
frameid [ /slotid ]	Indicates the shelf ID and slot ID. To query the description of all the boards of a shelf or a specified board, use this parameter.	Character string type, a string of 1-15 characters.

Modes

User mode

Level

Common user level

Usage Guidelines

When you specify only the shelf ID, the information about all the boards in the shelf is queried. You can query the information, including the slot ID, board name, board state, and board online/offline state.
When the shelf ID and slot ID are specified, details of the specified board are displayed. You can query the information, including the board name, board state, and port information.
The total number of activated and deactivated ports is displayed when you query information about a service board and its ports.

You can query the board state to check whether the board is in the normal state currently. The following table describes the board state set.

Board State	Description	Whether You Need to Handle the Board/How to Handle the Board
Failed	Indicates the failed state.	You need to handle the board: After the fault is rectified, the board state becomes Normal.
Auto_find	Indicates the auto-find state.	You need to handle the board: Run the board confirm command to confirm the board. Then, the board state becomes Normal. You can configure or query the board only after the board is confirmed successfully.
Auto_load	Indicates the auto-load state. After the service board is inserted to the slot, the board sends its version information to the system. If the board software version is different from the software version saved in the flash memory of the control board, the system automatically loads the software from the flash memory.	You do not need to handle the board. The board state becomes Normal or Auto_find multiple times later.
Prohibited	Indicates the prohibited state. Run the board prohibit command to prohibit a board if the board is not in used according to the network deployment or the board is faulty and the fault needs to be located, diagnosed, and rectified.	Run the undo board prohibit command to unprohibit a prohibited board.
Shutdown(manual)	Indicates the manual shutdown state. When no service is configured on the port, you can run the board prohibit to manually power off the service board to reduce power consumption.	Run the board power-on command to power on the service board remotely.
Config	Indicates the configured state. The board enters the configured state automatically after being confirmed.	You do not need to handle the board. The board recovers seconds later.
Normal	Indicates the normal state.	You do not need to handle the board.

Check whether the board is not inserted or is inserted loosely.
Check whether the board program fails to be loaded.
Check whether the board hardware is faulty.

Example

To query the information about all the boards in shelf 0 on the device for CCUB, do as follows:

huawei>display board{ frameid[/slotid]<S><Length 1-15> }:0


  Command:

          display board 0

  -------------------------------------------------------------------------

  SlotID  BoardName  Status           SubType0 SubType1    Online/Offline

  -------------------------------------------------------------------------

  0       H831CCUB   Active_normal    GP1A     ASDA

  1       H832DSLD   Failed                                Offline

  2

  3

  4       H838ASRB   Normal

  5       H831PAIA   Normal

  -------------------------------------------------------------------------

To query the information about all the boards in shelf 0 on the device for CCUE, do as follows:

huawei>display board 0

  -------------------------------------------------------------------------

  SlotID  BoardName  Status           SubType0 SubType1    Online/Offline

  -------------------------------------------------------------------------

  0       H831CCUE   Active_normal             ASDA

  1       H838ASPB   Normal

  2       H835VDGE   Normal

  3       H838ASRB   Failed                                Offline

  4       H835ADLE   Normal

  5       H831PAIA   Normal

  -------------------------------------------------------------------------

To query the information about all the boards in slot 0/0 on the devicefor CCUB, do as follows:

huawei>display board{ frameid[/slotid]<S><Length 1-15> }:0/0


  Command:

          display board 0/0


  ---------------------------------------

  Board Name          : H831CCUB

  Board Status        : Active normal

  ---------------------------------------


  Subboard[0]: H831GP1A                        Status: Normal

  Subboard[1]: H836ASDA                        Status: Normal

  ------------------------------------------------------------------------------

  Port Port COMBO    Optic    MDI    Speed      Duplex    Flow- Active   Link

       Type Mode     Status          (Mbps)               Ctrl  State

  ------------------------------------------------------------------------------

     0 GE   electric -        auto   auto       auto      off   active   offline

  ------------------------------------------------------------------------------

  Note: For a 1000 M, electrical port in the full-duplex mode, setting MDI to

        any value is invalid

  -----------------------------------------------------------------------------

  Port  Port   ONU-ID  SN                Register      Link   Role     Active

        Type                             State         State           State

  -----------------------------------------------------------------------------

     1  GPON        -  48575443AC754C41  Unregistered  Down   -        -

  ------------------------------------------------------------------------------

To query the information about all the boards in slot 0/0 on the device for CCUE, do as follows:

huawei>display board 0/0

  ---------------------------------------

  Board Name          : H831CCUE

  Board Status        : Active normal

  ---------------------------------------


  Subboard[0]: H831UP2A                        Status: Normal

  Subboard[1]: H836ASDA                        Status: Normal

  ------------------------------------------------------------------------------

  Port Port COMBO    Optic    MDI    Speed      Duplex    Flow- Active   Link

       Type Mode     Status          (Mbps)               Ctrl  State

  ------------------------------------------------------------------------------

     0 GE   electric -        auto   auto_1000  auto_full off   active   online

  ------------------------------------------------------------------------------

  ------------------------------------------------------------------------------

  Port  15Min   15Min    24Hour  24Hour

        AlmProf WarnProf AlmProf WarnProf

  ------------------------------------------------------------------------------

     0        -        -       -        -

  ------------------------------------------------------------------------------

  Note: For a 1000 M, electrical port in the full-duplex mode, setting MDI to

        any value is invalid

  -----------------------------------------------------------------------------

  Port  Port   ONU-ID  SN                Register      Link   Role     Active

        type                             state         state           state

  -----------------------------------------------------------------------------

     1  GPON        -  4857544300000006  Unregistered  Down   -        -

  ------------------------------------------------------------------------------

To query the information about all the boards in slot 0/5 on the device, do as follows:

huawei>display board{ frameid[/slotid]<S><Length 1-15> }:0/5


  Command:

          display board 0/5


  ---------------------------------------

  Board Name          : H832PDVAA

  Board Status        : Normal

  ---------------------------------------


  Subboard[0]: H831VPBA                        Status: Normal

  --------------------------------------------

  Board Information   : DC Power Supply

  --------------------------------------------

  DC0                 : Normal

  DC1                 : --

System Response

The system displays the queried result when the command runs successfully.

The following table describes the parameters in response to the display board 0 command.

Parameter	Description
SlotID	Indicates the slot ID.
BoardName	Indicates the name of the board.
Status	Indicates the board state. It can be failed, auto_find, auto_load, prohibited, config, or normal. For details, see the board state set in the "Usage Guidelines."
SubType0	Indicates the name of daughter board 0.
SubType1	Indicates the name of daughter board 1.
Online/Offline	Indicates the board state. It can be online or offline. When the board state is offline, the line connection may be interrupted or damaged, or the port at the peer end or the local end is faulty. In addition, alarm 0x0a31a0dd The Ethernet port link status changes from up to down is reported. Clear the alarm according to the handle suggestions. After the alarm is cleared, the link state becomes online.

The following table describes the parameters in response to the display board 0/0 command.

Parameter	Description
Board Name	Indicates the name of the board.
Board Status	Indicates the board state. It can be failed. For details, see the board state set in the "Usage Guidelines."
Subboard	Indicates the name of the daughter board.
Status	Indicates the daughter board state. For details, see the board state set in the "Usage Guidelines."
Port	Indicates the port ID.
Port Type	Indicates the type of the port. The type varies with the board type.
COMBO Mode	Indicates the COMBO Mode of the port.
Optic Status	Indicates the optical module state. It can be normal or absence. When the optical module state is absence, the optical module may be installed improperly or is faulty. Alarm 0x0a31a0de The optical transceiver is absence is reported. Clear the alarm according to the handle suggestions. After the alarm is cleared, the optical module state becomes normal.
MDI	Indicates the medium dependent interface (MDI). It can be straight-through cable or crossover cable. The type of the cable connecting to the port must match the type of the configured cable. Run mdi the command to configure the cable adaptation mode of the Ethernet port.
Speed(Mbps)	Indicates the speed of the port. Unit: Mbit/s. It can be auto, 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Rates of the two ports through which two devices are connected must be the same. Otherwise, the communication may fail. Run the speed command to configure the rate of the Ethernet port.
Duplex	Indicates the duplex type. It can be half, full, or auto. Rates of the two ports through which two devices are connected must be the same. Otherwise, the communication may fail. Run the duplex command to configure the duplex type of the Ethernet port.
Flow-Ctrl	Indicates the flow control. It can be on or off. Run the flow-control command to enable the flow control on the Ethernet port.
Active State	Indicates the port activation state. It can be active or deactivate. The default state is active. When the state is deactivate, the port cannot transmit services and the services transmitted on the port is interrupted. Run the undo shutdown command to activate the port.
Link	Indicates the link state. It can be offline or online. When the link state is offline, the line connection may be faulty, or damaged, or the port at the local end or the remote end is faulty or manually disabled. In addition, alarm 0x0a31a0dd The Ethernet port link status changes from up to down is reported. Clear the alarm according to the handle suggestions. After the alarm is cleared, the optical module state becomes normal.
ONU-ID	Indicates the ID of the ONU.
SN	Indicates the sequence number.
Regist State	Indicates the registration state. It can be unregisted or registed.

Unregisted: The board does not register with the upper-layer OLT.
Registed: The board already registers with the upper-layer OLT.
on: The flow control on the Ethernet port is enabled. When the flow on the Ethernet port is heavy, the system enables the flow control.
off: The flow control on the Ethernet port is disabled.

The following table describes the parameters in response to the display board 0/5 command.
Parameter
Description
Board Name
Indicates the name of the board.
Board Status
Indicates the board state.
Board Information
Indicates the information of the board.
For more information about the error message that the system displays against a command entered with incorrect syntax, refer to "Syntax Check" in Parameter.

Good Luck!

Thanks

H835ADLE Not Showing Ports; SmartAX MA5616

Best answer

Recommended answer

display board

Function

Format

Parameters

Modes

Level

Usage Guidelines

Example

System Response

Third Party’s Trade Secret

My Followers

Enterprise

Consumer

Corporate

Carriers

H835ADLE Not Showing Ports; SmartAX MA5616

Best answer

Recommended answer

display board

Function

Format

Parameters

Modes

Level

Usage Guidelines

Example

System Response

Third Party’s Trade Secret

My Followers