H806GPBD board failed to load on MA5608T
Hi there, all!
This post is about the issue that the H806GPBD board failed to load on MA5608T. Please see more details below.
Source: https://www.thunder-link.com/H806GPBD_p672.html
ISSUE DESCRIPTION
MA5608T#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0 H806GPBD Failed Online
1
2 H801MCUD1 Active_normal CPCB
3 H801MCUD1 Standby_normal CPCB
4 H801MPWC Normal
5
-------------------------------------------------------------------------
MA5608T#
MA5608T#display version
{ <cr>|backplane<K>|frameid/slotid<S><Length 1-15> }:
Command:
display version
VERSION : MA5600V800R015C00
PATCH : SPH105
PRODUCT : MA5608T
Active Mainboard Running Area Information:
--------------------------------------------------
Current Program Area : Area A
Current Data Area : Area A
Program Area A Version : MA5600V800R015C00
Program Area B Version : MA5600V800R015C00
Data Area A Version : MA5600V800R015C00
Data Area B Version : MA5600V800R015C00
--------------------------------------------------
Standby Mainboard Running Area Information:
--------------------------------------------------
Current Program Area : Area A
Current Data Area : Area A
Program Area A Version : MA5600V800R015C00
Program Area B Version : MA5600V800R015C00
Data Area A Version : MA5600V800R015C00
Data Area B Version : MA5600V800R015C00
--------------------------------------------------
Uptime is 2 day(s), 16 hour(s), 8 minute(s), 9 second(s)
Please assist me with solving the issue that the H806GPBD board failed to load on MA5608T. Thanks!
- x
- convention：
- Emotion(0)
|
Hello there! Service Board Is in the Failed State This topic describes how to troubleshoot the fault through the CLI when the service board of the MA5600T/MA5603T/MA5608T is in the failed state. Location Method When the service board of the MA5600T/MA5603T/MA5608T is in the failed state, locate the fault according to the following procedure:
 NOTICE:To facilitate fault report, save the results of the following steps. When you remove and insert a service board, antistatic measures must be taken. Procedure
If it is confirmed that system configurations are correct, insert a board of the correct type into the slot and then proceed to the next step. If it is confirmed that system configurations are incorrect, run the board delete command to delete the original configurations, after the system displays a message indicating that the board is auto discovered, run the board confirm command to confirm the board and then proceed to the next step. Wait five minutes and then check whether the fault is rectified. Check whether the service board is firmly inserted.
Check whether the fault is rectified. Check whether the power supply of the cabinet is normal.
Check whether the fault is rectified. Replace the original service board, and then check whether the new service board can start normally.
In the diagnosis mode, run the display reset-record command. Connect Huawei for technical support. The fault is rectified. |
|
|
Hello there! Service Board Is in the Failed State This topic describes how to troubleshoot the fault through the CLI when the service board of the MA5600T/MA5603T/MA5608T is in the failed state. Location Method When the service board of the MA5600T/MA5603T/MA5608T is in the failed state, locate the fault according to the following procedure:
NOTICE:To facilitate fault report, save the results of the following steps. When you remove and insert a service board, antistatic measures must be taken. Procedure
If it is confirmed that system configurations are correct, insert a board of the correct type into the slot and then proceed to the next step. If it is confirmed that system configurations are incorrect, run the board delete command to delete the original configurations, after the system displays a message indicating that the board is auto discovered, run the board confirm command to confirm the board and then proceed to the next step. Wait five minutes and then check whether the fault is rectified. Check whether the service board is firmly inserted.
Check whether the fault is rectified. Check whether the power supply of the cabinet is normal.
Check whether the fault is rectified. Replace the original service board, and then check whether the new service board can start normally.
In the diagnosis mode, run the display reset-record command. Connect Huawei for technical support. The fault is rectified. |
|
Comment
- Politically sensitive content
- Content concerning pornography, gambling, and drug abuse
- Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
