Got it
Huawei Enterprise Support Community
Community Forums Cloud & Big Data
fusion sphere installatio...

fusion sphere installation

Created: Jul 26, 2018 11:04:51Latest reply: Oct 23, 2018 13:16:58 1195 4 0 0 1
  Rewarded HiCoins： 0 (problem resolved)
View the author 1#
I'm  trying to install  FusionSphere private cloud non_cascading  using FusionAccess but it keeps saying "FusionSphere basic installation failed ,can not  find dhcp port "

Like (0) Dislike (0) Favorite(1) Share Report
Previous: fusionsphere ressources
Next: Kerberos Client Installation Steps
Featured Answers

Recommended answer

(0) (0)
olive.zhao
Admin Created Oct 23, 2018 13:16:58

This post was last edited by ganmianpi at 2018-10-23 13:19.

•Storage media (such as a local disk) has been planned for the OS to be installed on the host.
NOTE:
◾If the space of a hard disk or RAID disk is greater than 2 TB, the system identifies it only as a 2 TB disk.

•Hosts have been configured based on requirements. For details about the requirements, see Server Configuration Requirements.
•Hosts to be installed support booting from the network.
•You have obtained the base board management controller (BMC) IP address of the host if the host has BMC installed.
NOTE:
The BMC manages host hardware using Intelligent Platform Management Interfaces (IPMIs), and is responsible for remote access, control, and management functions of a host.

•You have obtained the basic input/output system (BIOS) passwords of the hosts if these passwords have been configured.
•The local PC meets the following requirements:
◾The PC runs one of the following 32-bit or 64-bit OSs:◾Windows XP
◾Windows 7
◾Windows Server 2003
◾Windows Server 2008

◾The Windows firewall and other network management software of the local PC are disabled.
◾The local PC has a minimum of one disk with available space of greater than 5 GB.
◾The DHCP, TFTP, or FTP service is not installed and started on the local PC.
◾The local PC is properly communicating with the management plane and BMC plane of the hosts. You are advised to connect the PC and the hosts to be installed to the same switch and set their IP addresses to the same management network segment, unless the management plane has a virtual local area network (VLAN) configured.
◾The local PC is properly communicating with the installation plane, which is the network plane that assigns DHCP addresses and is used for installing hosts. You are advised to use the management plane as the installation plane. If the IP address of the local PC is not in the installation plane network segment, configure the DHCP relay on the switch. For details, see Example of Configuring Switch.
NOTE:
◾Do not add VLAN tags to packets passing through the PXE port during the PXE boot process. Configure network settings to allow these packets to pass through the port.

◾The system time is set correctly on the local PC.

•Except the DHCP server provided by this tool, no other DHCP servers are running in the installation plane subnet during host installation.
•Servers in the installation plane network, except hosts to be installed, do not require DHCP addresses

if you want know more detail , please check the follow link:

http://support.huawei.com/enterprise/en/doc/EDOC1000162752?idPath=7919749|7919788|9856606|21462752|9823560

 

View more
  • x
  • convention：
All Answers
(0) (0)
2#
George.adel
George.adel Created Jul 26, 2018 11:17:18

◾The local PC is properly communicating with the installation plane, which is the network plane that assigns DHCP addresses and is used for installing hosts. You are advised to use the management plane as the installation plane. If the IP address of the local PC is not in the installation plane network segment, configure the DHCP relay on the switch. For details, see Example of Configuring Switch.
NOTE:
◾Do not add VLAN tags to packets passing through the PXE port during the PXE boot process. Configure network settings to allow these packets to pass through the port.

◾The system time is set correctly on the local PC.

•Except the DHCP server provided by this tool, no other DHCP servers are running in the installation plane subnet during host installation.
•Servers in the installation plane network, except hosts to be installed, do not require DHCP addresses.

View more
  • x
  • convention：
(0) (0)
3#
cloud123
cloud123 Created Jul 27, 2018 08:27:59

Posted by George.adel at 2018-07-26 11:17 ◾The local PC is properly communicating with the installation plane, which is the network plane tha ...
i 'm working with windows 7 i don't have access to dhcp server i don't know the ip address of the server even I've tried to set up a vlan and didn't found the vlan option in the NIC that I'm was planning to create the vlan from ,and I'm only working with one host
View more
  • x
  • convention：
(0) (0)
4#
Jorgec81
Jorgec81 Created Aug 3, 2018 21:20:31

He refers to the local DHCP that is created when you launch the Installation program, you need to be sure that your installation PC is connected to the Service plane of the Host you are going to install not the Management plane (iBMC for example)
View more
  • x
  • convention：
(0) (0)
5#
olive.zhao
olive.zhao Admin Created Oct 23, 2018 13:16:58

This post was last edited by ganmianpi at 2018-10-23 13:19.

•Storage media (such as a local disk) has been planned for the OS to be installed on the host.
NOTE:
◾If the space of a hard disk or RAID disk is greater than 2 TB, the system identifies it only as a 2 TB disk.

•Hosts have been configured based on requirements. For details about the requirements, see Server Configuration Requirements.
•Hosts to be installed support booting from the network.
•You have obtained the base board management controller (BMC) IP address of the host if the host has BMC installed.
NOTE:
The BMC manages host hardware using Intelligent Platform Management Interfaces (IPMIs), and is responsible for remote access, control, and management functions of a host.

•You have obtained the basic input/output system (BIOS) passwords of the hosts if these passwords have been configured.
•The local PC meets the following requirements:
◾The PC runs one of the following 32-bit or 64-bit OSs:◾Windows XP
◾Windows 7
◾Windows Server 2003
◾Windows Server 2008

◾The Windows firewall and other network management software of the local PC are disabled.
◾The local PC has a minimum of one disk with available space of greater than 5 GB.
◾The DHCP, TFTP, or FTP service is not installed and started on the local PC.
◾The local PC is properly communicating with the management plane and BMC plane of the hosts. You are advised to connect the PC and the hosts to be installed to the same switch and set their IP addresses to the same management network segment, unless the management plane has a virtual local area network (VLAN) configured.
◾The local PC is properly communicating with the installation plane, which is the network plane that assigns DHCP addresses and is used for installing hosts. You are advised to use the management plane as the installation plane. If the IP address of the local PC is not in the installation plane network segment, configure the DHCP relay on the switch. For details, see Example of Configuring Switch.
NOTE:
◾Do not add VLAN tags to packets passing through the PXE port during the PXE boot process. Configure network settings to allow these packets to pass through the port.

◾The system time is set correctly on the local PC.

•Except the DHCP server provided by this tool, no other DHCP servers are running in the installation plane subnet during host installation.
•Servers in the installation plane network, except hosts to be installed, do not require DHCP addresses

if you want know more detail , please check the follow link:

http://support.huawei.com/enterprise/en/doc/EDOC1000162752?idPath=7919749|7919788|9856606|21462752|9823560

 

View more
  • x
  • convention：
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.