ether-trunk in router Ne40m2k

Created: Nov 9, 2019 21:17:34Latest reply: Nov 11, 2019 18:39:39 85 2 0 0
  Rewarded Hi-coins: 0 (problem resolved)

I have a problem making an ether-trunk on the router. In the sw I do quiet. but on the router when I try to add ports to trunk he says that the interfaces are l3 and not let add. would you have another way of doing this? because I need to do a 20Gb trnk for a sw all huawei no sw is quiet. already on the router I have is as I mentioned above


  • x
  • convention:

Featured Answers
gabo.lr
MVE Created Nov 11, 2019 18:39:39 Helpful(0) Helpful(0)

Hello!!

Here is some info from Huawei documentation about Eth-trunk:


Usage Scenario

You can run the eth-trunk command to add physical interfaces to an Eth-Trunk interface to increase the bandwidth, improve reliability, and perform load balancing.

You can run the undo eth-trunk command in the view of a member interface to delete the member interface from the Eth-Trunk interface. You can also run the undo trunkport command in the Eth-Trunk interface view to delete a member interface from an Eth-Trunk interface.

Prerequisites

  • The Eth-Trunk interface to which Ethernet interfaces will be added has been successfully created.

  • Ethernet interfaces are not configured with any service. For example:

    • Layer 3 configurations such as IP addresses

    • Static MAC entries


Hope thats clear

Best regards

  • x
  • convention:

Peterhof
Peterhof Created Nov 12, 2019 03:59:50
Hello! Maybe in this case it will be good idea to create Eth-Trunk at the level 2 in the switch and in the router, and after that to create required L3 configuration at the router in the Eth-Trunk interface instead of physical interfaces that are configured as L3 now.  
All Answers
gabo.lr
gabo.lr MVE Created Nov 11, 2019 18:39:39 Helpful(0) Helpful(0)

Hello!!

Here is some info from Huawei documentation about Eth-trunk:


Usage Scenario

You can run the eth-trunk command to add physical interfaces to an Eth-Trunk interface to increase the bandwidth, improve reliability, and perform load balancing.

You can run the undo eth-trunk command in the view of a member interface to delete the member interface from the Eth-Trunk interface. You can also run the undo trunkport command in the Eth-Trunk interface view to delete a member interface from an Eth-Trunk interface.

Prerequisites

  • The Eth-Trunk interface to which Ethernet interfaces will be added has been successfully created.

  • Ethernet interfaces are not configured with any service. For example:

    • Layer 3 configurations such as IP addresses

    • Static MAC entries


Hope thats clear

Best regards

  • x
  • convention:

Peterhof
Peterhof Created Nov 12, 2019 03:59:50
Hello! Maybe in this case it will be good idea to create Eth-Trunk at the level 2 in the switch and in the router, and after that to create required L3 configuration at the router in the Eth-Trunk interface instead of physical interfaces that are configured as L3 now.  

Comment

Reply
You need to log in to reply to the post Login | Register

Notice Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Login and enjoy all the member benefits

Login and enjoy all the member benefits

Login