Got it

ENSP Command not working on CE 6800 switch

Created: Aug 11, 2017 11:57:12Latest reply: Sep 1, 2017 10:11:54 1702 6 0 0
  Rewarded HiCoins: 0 (problem resolved)
Dear friends i am trying to run below mentioned command on CE 6800 switch to complete my ENSP Vlan lab but this command is not working. please help.



[~HUAWEI-GE1/0/0]port mux-vlan enable vlan 2

  • x
  • convention:

Featured Answers

Recommended answer

mangix
Created Aug 26, 2017 01:39:10 Helpful(0) Helpful(0)

The firmware version of ENSP only support the command “port mux-vlan enable”,not support “port mux-vlan enable vlan 2”,in that firmware version,the interface can only add to one vlan if use mux-vlan
View more
  • x
  • convention:

New_Commer--->切换到此号
All Answers
WoodWood
WoodWood Created Aug 14, 2017 01:46:31 Helpful(0) Helpful(0)

please help,thanks@kmyd @撒么
View more
  • x
  • convention:

mangix
mangix Created Aug 14, 2017 03:22:03 Helpful(0) Helpful(0)

what's the information after running this commmand
View more
  • x
  • convention:

New_Commer--->切换到此号
user_2755255
user_2755255 Created Aug 16, 2017 02:24:58 Helpful(0) Helpful(0)

Posted by y00197467 at 2017-08-14 03:22 what's the information after running this commmand
Thankyou for your prompt response.

The information after running this command is given below.

[~HUAWEI-GE1/0/0]port mux-vlan enable vlan 2
^
Error: Too many parameters found at '^' position.
[~HUAWEI-GE1/0/0]


Please guide.
View more
  • x
  • convention:

user_2755255
user_2755255 Created Aug 18, 2017 03:20:40 Helpful(0) Helpful(0)

Dear users please help. :(
View more
  • x
  • convention:

mangix
mangix Created Aug 26, 2017 01:39:10 Helpful(0) Helpful(0)

The firmware version of ENSP only support the command “port mux-vlan enable”,not support “port mux-vlan enable vlan 2”,in that firmware version,the interface can only add to one vlan if use mux-vlan
View more
  • x
  • convention:

New_Commer--->切换到此号
m7g
m7g Created Sep 1, 2017 10:11:54 Helpful(0) Helpful(0)

This post was last edited by m7g at 2017-09-01 05:22. The port-mux-vlan enable command enables the MUX VLAN function on an interface
vlan 2 may be reserved vlan and it will can't be used here
The value of vlan-id1 -> 1 to 4094 (except reserved VLANs)

ps. Before enable MUX VLAN funtion, need:

1) The port has been added to a principal or subordinate VLAN as an access, hybrid, or trunk interface
2) port-security enable did't work with port mux-vlan enable
3) disable MAC address learning or limiting the number of learned MAC addresses on an interface affects the MUX VLAN funtion on the interface
4) You can create a VLANIF interface for a principal VLAN, but cannot create a VLANIF interface for a subordinate group VLAN or separate VLAN.
5) Interface enabled with the MUX VLAN function cannot be added to other VLANs of the MUX VLAN group

View more
  • x
  • convention:

WBR, Evgeny K.
-----------------
Mark my post "BEST ANSWER" if my post / answer

Comment

You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."

My Followers

Login and enjoy all the member benefits

Login

Huawei Enterprise Support Community
Huawei Enterprise Support Community
Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.