DSLAM MA5616 as PPPoE Client

Hi, friend!
Can you provide the version number of the device and the specific model of the main control board? 

Thanks!

Hi Chenxintao,

Please find below the requested details,

MA5616>display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0 H831CCUB Active_normal EP1A ASDA
1 H83BVDLE Auto_find
2
3
4
5 H831PAIA Normal
-------------------------------------------------------------------------

Thanks.

Hello, friend!

1. You can run the board add 0/1 VCM command to add a board.

2. Run the vlan 100 smart command.

3. Run the port vlan 100 0/0 command.

4. Run the service-port vlan 100 vdsl mode ptm multi-service user-vlan 100 command.

5. Run the simulate pppoe command to perform analog dialup.

6. Run the display simulation pppoe command to check the analog dialup result.

Of course, you can change the VLAN ID in the command to the configured VLAN ID.

If you only to verify the connectivity, add a virtual board, configure the service flow and VLAN, and then use the simulated PPPoE command to simulate dialup.

Thanks!

Thank you Chenxintao, I'll check these configuration and get back to you.

Hi Chenxintao,
I'm facing some issues while do the above configuration,

1. While adding the board,
MA5616(config)#board add 0/1 VCM
^
% Unknown command, the error locates at '^'

MA5616(config)#board add 0/1 VDL
1 [2000-03-02 05:15+08:00]:
A board auto disappear,FrameID:0,SlotID:1,Board_name:H83BVDLE

MA5616(config)#
0 frame 1 slot board added successfully
! FAULT MAJOR 2000-03-02 05:15+08:00
ALARM NAME :The communication between the board and the control board fails
PARAMETERS :FrameID: 0, SlotID: 1, Board Name: VDL

MA5616(config)#
! RECOVERY CLEARED 2000-03-02 05:15+08:00
ALARM NAME :The communication of the board with the control board recovers
PARAMETERS :FrameID: 0, SlotID: 1, Board Name: H83BVDLE

2. Error thrown when trying to set service port,

MA5616(config)#service-port vlan 7 vdsl mode ptm 0/0/0
{ <cr>|inbound<K>|multi-service<K>|rx-cttr<K> }:multi-service
{ user-8021p<K>|user-encap<K>|user-vlan<K> }:user-vlan
{ other-all<K>|priority-tagged<K>|untagged<K>|user-vlanid<U><1,4095> }:7
{ <cr>|bundle<K>|inbound<K>|rx-cttr<K>|user-encap<K> }:

Command:
service-port vlan 7 vdsl mode ptm 0/0/0 multi-service user-vlan 7

Kindly help me on this to resolve this. Thanks in advance.

Good answer

Hello, friend!

0/0/0 is an upstream port and cannot be used to create service flows. You can create service flows on 0/1, for example, 0/1/0.

service-port vlan 7 vdsl mode ptm 0/1/0 multi-service user-vlan 7

Thanks!

Good

Thank Chenxintao, change in port number worked for me.
But after starting the PPPoE Simulation, it is failing for me.

MA5616(config)#

PPPOE simulation has failed

Can you please share any debug commands that we can use to check whether the pkts are forwarded or not?

Also if possible can you please share PPPoE commands related documents ?