Scenarios
Log in to FusionCompute to centrally manage virtual, service, and user resources.
Prerequisites
- The browser for logging in to FusionCompute is available.
- The Internet Explorer or Mozilla Firefox is set properly. For details, see Setting Internet Explorer Browser (FusionCompute) or Setting Mozilla Firefox Browser.
- The browser resolution is set to 1280 x 1024 or higher based on the service requirement to ensure the optimum display effect on the FusionCompute.
NOTE:If the security certificate has not been installed during Internet Explorer configuration, the browser may prompt users with a web page display exception message when they log in to FusionCompute for the first time or log in to VMs using Virtual Network Computing (VNC). In this case, press F5 to refresh the web page.
The system supports the following browsers:
- Internet Explorer 10 to Internet Explorer 11
- Mozilla Firefox 34 to Mozilla Firefox 55
- Google Chrome 31 to Google Chrome 60
Data
Table A-5 lists the data required for performing this operation.
Parameter | Description | Example Value |
|---|---|---|
IP address of the VRM node | Specifies the floating IP address of the Virtual Resource Management (VRM) nodes if the VRM nodes are deployed in active/standby mode, or the management IP address of the VRM node if only one VRM mode is deployed. | 192.168.40.3 |
Username/Password | Specifies the username and password used for logging in to FusionCompute. | admin/Admin@123 In common mode, the username and password are admin/Huawei@CLOUD8!. In rights separation mode, the username and password are as follows:
|
User type | Specifies the type of the user to log in to the system. Value:
| Local user |
Login type | Specifies the login type. Value:
| Local |
Procedure
- Open Internet Explorer.
- Enter http://VRM node IP address and press Enter.
If two VRM nodes are deployed, the IP address is the floating IP address of the VRM nodes. If only one VRM node is deployed, the IP address is the management IP address of the VRM mode.
NOTE:- If a firewall is deployed between the local PC and FusionCompute, open ports 80, 8080, 43, and 8443 on the firewall. If ports 80 and 8080 cannot be opened on the firewall, enter https://IP address of the VRM node:8443 in the address box.
- If Internet Explorer slows down after running for a period of time and no data is required to be saved, press F6 on the current page to move the cursor to the address bar of the browser. Then, press F5 to refresh the page and increase the browser running speed.
The login page is displayed.
After the SSO is configured, if you open the login page of the FusionCompute, the system switches to the login page of the FusionManager. However, multiple users cannot log in to the FusionCompute using the same account.
- Perform the required operation based on the login page.
- If the FusionCompute login page shown in Figure A-4 is displayed, single sign-on (SSO) is not configured. Go to Step 4.
- If the FusionManager login page shown in Figure A-5 is displayed, SSO has been configured. Go to Step 5.
- Set the Username and Password, select the required User type and Login type, and click Login. If you attempt to log in to the system again after the initial login fails, you must also set the Verification code.
The initial login username is admin and the password is Admin@123.
Enter the username and password based on the rights management mode configured during VRM installation.
- Common login mode: The initial login username is admin and the password is Huawei@CLOUD8!.
- Rights separation login mode: The username and password of the system administrator is sysadmin/Sysadmin#, the username and password of the security administrator is secadmin/Secadmin#, and the username and password of the security auditor is secauditor/Secauditor#.
NOTE:- If it is your first login using the admin username, the system asks you to change the password of the admin username.
- The new password must meet the following requirements:
- It contains a minimum of sixeight characters and a maximum of 32 characters.
- It contains at least one space or one of the following special characters: `~!@#$%^&*()-_=+\|[{}];:'",<.>/?`~!@#$%^&*()-_=+|[{}];:,./?.
- It contains at least two types of the following characters: uppercase letters, lowercase letters, and digits.
The FusionCompute operation page is displayed after you log in to the system.
The login operation is complete.
- Set the Username and Password. If you attempt to log in to the system again after the initial login fails, you must also set the Verification code.
The default username is geadmin and password is Admin@123.
- Common login mode: Log in to the system using the FusionManager system account. After the login, you can only perform query-related operations.
- Rights separation login mode: The username and password of the system administrator is sysadmin/Sysadmin#, the username and password of the security administrator is secadmin/Secadmin#, and the username and password of the security auditor is secauditor/Secauditor#.
- Click Login to log in to the FusionCompute management system. NOTE:The user is automatically logged out of the FusionCompute management system if one of the following conditions is met:
- The current user's session times out.
- The system administrator deletes the current user.
- The system administrator manually locks the current user out.
- The current user has logged in to another client or use another browser to log in to FusionCompute.
- The maximum number of connections allowed by the current user has been changed to a small value, and the number of login sessions of this user has exceeded the changed number.
After you log in to FusionCompute, you can learn the system and its functions from the online help, product tutorial, and alarm help. If you save the URLs of the documents, you can access them even when you are logged out of the FusionCompute system.
