Description of OSPF route fields on the AR router

33

Destination: indicates the destination route.
Cost: indicates the cost to the route.
Type: specifies the type of the destination route, which can be stub or transit.
AdvRouter: specifies the device that advertises the route, that is, router ID of the router that generates the LSA.
Area: specifies the area in which the route is learned.
Priority: specifies the priority of the route.

Other related questions:
Description of the E1 interface of an AR router
1. E1/T1: E1/T1 is a technology of using the synchronous time division multiplexing technology to combine multiple audio channels into a 2 Mbit/s or 1.5 Mbit/s high-speed channel. - Maximum rate of E1 cards: 32 (timeslots) x 64 (kbit/s per timeslot) = 2048 kbit/s - Maximum rate of T1 cards: 24 (timeslots) x 64 (kbit/s per timeslot) = 1536 kbit/s - CE1/CT1 cards can determine multiple groups of timeslots and have the Controller view. However, E1 cards can determine only one group of timeslots in the framed mode (other timeslots cannot be used). 2. E1 interfaces are configured on E1/T1 cards and can be seen as serial interfaces (currently supported by AR1200(S)/AR2200(S)/AR3200(S)/AR3600). - 1E1T1-M/2E1T1-M support the E1/CE1/CT1/PRI(E1&T1) interface. - 4E1T1-M/8E1T1-M support the E1/CE1/PRI(E1) interface. - 1E1T1-F/2E1T1-F support the framed/unframed E1/T1 interface. - 4E1T1-F/8E1T1-F support the framed/unframed E1 interface. - The character M in a model name indicates Multiflex Trunk, that is, the model can be fully channelized. The character F in a model name indicates Fractional, that is, the model can be partially channelized. 3. The CE1/PRI interface is the physical interface of the E1 system. It can work in E1 mode (unchannelized mode) or CE1/PRI mode (channelized mode). - In E1 mode, the CE1/PRI interface works as an interface not divided by timeslots, whose bandwidth is 2.048 Mbit/s. - In CE1/PRI mode, the 2M line is divided into 32 timeslots of 64 KB, which are numbered from 0 to 31. Timeslot 0 is used to transfer frame alignment information. a. CE1 interface: All timeslots except timeslot 0 are randomly divided into multiple groups (channel sets). Each group is corresponding to a separated channel. b. PRI interface: Bundle timeslot 16 (D channel) and any one of timeslots 1 to 15 or 17 to 31 (B channel) into a group (PRI set). c. CE1 interfaces can be divided into multiple groups. However, only one group can be bundled for PRI interfaces. 4. The CT1/PRI interface is the physical interface of the T1 system. - CT1 interface: All timeslots (timeslot 1 to 24) can be randomly divided into multiple groups. Timeslots in each group are bundled into a channel set. - PRI interface: Randomly bundle timeslot 24 (D channel) and any one of timeslots 1 to 23 (B channel) into a group (PRI set). - CT1 interfaces can be divided into multiple groups. However, only one group can be bundled for PRI interfaces. 5. E1 interfaces, channel sets, and PRI sets can all be seen as serial interfaces, which have the same logical characteristics as synchronous serial interfaces and support IP network protocols and protocols in the data link layer, such as PPP and HDLC frame relay X.25 protocol (PRI sets do not support the HDLC frame relay X.25 protocol and channel sets of CT1 interfaces do not support the X.25 protocol).

How to configure OSPF to filter routes based on a routing policy
OSPF can use routing policies to filter routes. By default, OSPF does not filter routes. To configure OSPF to filter the routes to be received, run the filter-policy import command. To configure OSPF to filter the routes to be sent, run the filter-policy export command. You can use one of the following routing policies: 1. Basic ACL 2. Advanced ACL 3. IP prefix list 4. Route-policy

What does the TOS field in an OSPF LSA indicate
The TOS field in an OSPF LSA was designed for QoS routing. Packets with different TOS values are transmitted on links with different cost values, enabling TOS-based routing. That is, IP packets with the same destination but different TOS values are forwarded on differentiated routes. This application, however, is canceled in RFC 2328. The OSPF devices support only TOS value 0. That is, the route is based only on destination IP address.

Description of the GIADDR field in DHCP packets
For S series switches, the giaddr field in DHCP packets has the following function: The giaddr field (gateway IP address) indicates the IP address of the first DHCP relay agent that DHCP packets pass through. If the DHCP server and client are located on different network segments, the first DHCP relay agent fills its IP address into this field of the DHCP Request packet sent by the client and forwards the packet to the DHCP server. The DHCP server determines the network segment where the client resides based on this field, and allocates an IP address on this network segment from an address pool.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top