Can the peak record of an interface on an AR router be cleared

20

In V200R006 and later versions, run the reset counters interface command to clear the peak record. In versions earlier than V200R006, the peak record cannot be cleared.

Other related questions:
How to clear alarms on AR routers
Run the clear alarm active command on the device to clear the active alarms of the device. After the command is run, the system will clear all active alarms on the device. Clear alarms with caution because cleared active alarms cannot be recovered.

How do AR routers support sub-interfaces
AR routers support sub-interfaces as follows: Only Layer-3 Ethernet interfaces support the configuration of sub-interfaces. AR routers of different models and versions have no differences in the support of sub-interfaces.

Does an AR router support an interface being switched over between Layer 2 and Layer 3
The following AR routers support an interface being switched over between Layer 2 and Layer 3. By default, Ethernet interfaces are Layer 2 interfaces. Run the undo portswitch command to switch the interfaces from Layer 2 mode to Layer 3 mode, and run the portswitch command to switch the interfaces back to Layer 2 mode. V200R006C00 and earlier versions: - AR150 and AR200 series: Eth0/0/0 - AR120-S series: Eth0/0/0~Eth0/0/3 - AR150-S, AR160-S, and AR200-S series (except for AR151-S2): Eth0/0/0 - AR151-S2: GE0/0/0 - AR160 series: GE0/0/0 - AR1220F: Eth0/0/0~Eth0/0/7 - AR2201-48FE, AR2202-48FE, and AR2201-48FE-S: Eth0/0/0 and Eth0/0/47 V200R007C00: - AR120 and AR150 series, AR120-S series, AR151-S, AR151W-P-S, and AR151G-U-S: Eth0/0/0~Eth0/0/3 - AR160 series, AR509G-L-D-H, AR110-S series, AR151-S2 and AR160-S series: GE0/0/0~GE0/0/3 - AR200 series, AR1220, AR1220V, AR1220W, AR1220VW, AR1220F, AR200-S series, AR1220-S, AR1220W-S, and AR1220F-S: Eth0/0/0~Eth0/0/7 - AR1220C, AR1220E, AR1220EV, AR1220EVW, and AR1220E-S: GE0/0/0~GE0/0/7 - AR2201-48FE and AR2202-48FE: Eth0/0/0~Eth0/0/47 - AR2204-51GE-P: GE0/0/3~GE0/0/50 - AR2204-27GE-P, AR2204-27GE, and AR2201-48FE-S: GE0/0/3~GE0/0/26 V200R008C00: - AR120 (except for AR129CGVW-L) and AR150 series, AR120-S series, AR151-S, AR151W-P-S, and AR151G-U-S: Eth0/0/0~Eth0/0/3 -AR100 series, AR160 series, AR129CGVW-L, AR503EW, AR503EDGW-Lc, AR509CG-Lt, AR509CG-Lc, AR509G-Lc, AR515GW-LM9-D and AR509G-L-D-H, AR100-S series, AR110-S series, AR151-S2 and AR160-S series: GE0/0/0~GE0/0/3 - AR200 series, AR1220, AR1220V, AR1220W, AR1220VW, and AR1220F, AR200-S series, AR1220-S, AR1220W-S, and AR1220F-S series: Eth0/0/0~Eth0/0/7 - AR1220C, AR1220E, AR1220EV and AR1220EVW, and AR1220E-S: GE0/0/0~GE0/0/7 - AR2201-48FE, AR2202-48FE, and AR2201-48FE-S: Eth0/0/0 and Eth0/0/47 - AR2204-51GE-P, AR2204-51GE-R, and AR2204-51GE: GE0/0/3~GE0/0/50 - AR2204-27GE-P and AR2204-27GE: GE0/0/3~GE0/0/26 At present, the interfaces of all cards do not support Layer 2 and Layer 3 interface switchover.

How to delete SNMP configuration on an AR router
Run an undo command corresponding to the SNMP feature to delete SNMP configuration from an AR router.

Can an interface range be mapped on the AR router
The AR router cannot map an interface range.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top