Do ACs support the APs whose models start with WA


The AC6605 supports the WA6x3xN series, but only V200R002 and V200R001 support this series.
To manage the WA series APs, check whether the AC6605 version is V200R002 or an earlier version. If the AC6605 version is later than V200R002, an earlier version needs to be used (the AC and AP versions must match).
The AC6605 of V200R003 and later versions do not support the WA6x3xN series APs.

Other related questions:
How to check whether the AP model is supported by the AC?
Apply this command in user view: display ap-type all If the AP model is not in the above list, it is not supported by the AC.

APs supported by the AC
Run the display ap-type all command on the AC to view APs supported by the AC. For example: [AC-wlan-view] display ap-type all All AP types information: ----- ID Type ----- 17 AP6010SN-GN 19 AP6010DN-AGN 21 AP6310SN-GN 23 AP6510DN-AGN 25 AP6610DN-AGN 27 AP7110SN-GN 28 AP7110DN-AGN 29 AP5010SN-GN 30 AP5010DN-AGN 31 AP3010DN-AGN 33 AP6510DN-AGN-US 34 AP6610DN-AGN-US 35 AP5030DN 36 AP5130DN 37 AP7030DE 38 AP2010DN 39 AP8130DN 40 AP8030DN 42 AP9330DN ----- Total number: 19

Which AP models support mode switching
APs that support mode switching: AP3010DN-AGN, AP5010SN-GN, AP5010DN-AGN, AP5030DN, AP5130DN, AP6010SN-GN, AP6010DN-AGN, AP6510DN-AGN, AP6510DN-AGN-US, AP6610DN-AGN, AP6610DN-AGN-US, AP3030DN, AP4030DN, AP4130DN, AP7110DN, AP8030DN, AP8130DN, AP3010DN-V2, AP5030DN-S, AP9131DN, AP9132DN, AD9430DN-24, and AD9430DN-12 Note that APs only in V200R003 or later support the Fat mode, so APs in versions earlier than V200R003 (such as WA series APs) do not support mode switching.

Which AP models can be upgraded remotely
For information about the AP models that support remote upgrade, see FAQ-哪些AP可以远程升级.

The AC fails to start
Two scenarios for AC start failure are as follows: - The AC can be powered on but cannot start, and the serial port does not display information. Rectify this fault by performing the following steps: 1. Check whether the power module functions properly. a. Measure the input voltage. Use a multimeter to measure the input voltage of the power module, and check whether the input voltage is in the operating voltage range of the power module. b. Remove and reinstall the power module. Unplug and plug the power module and its power cable to ensure that they are securely installed. c. Perform a cross test of the power module. Move the power module to another AC or replace it with another power module that can work normally in another AC, to determine whether the power module or the AC itself is faulty. If the test proves that the power module is faulty, send the power module back for repair. d. If the fault still occurs on the AC after the cross test, contact Huawei technical support. 2. Check whether there is obvious yellow mark on the interface. If the color of the connector turns yellowish, the fault may be caused by lightning strikes or surge current. The internal CPU chip may be damaged. In this case, dial Huawei customer service hotline and return the AC for repair (select the cause: F009 unexpected damage). Note: To protect the AC from lightning strikes or surge voltage, install a surge protector or a voltage stabilizer to ensure a stable running environment. 3. If there is no obvious mark, contact Huawei technical support. - The AC can be powered on and the serial port can display information, but the AC cannot start. a. If information can be displayed through the serial port, press Ctrl+B to enter the BootROM menu during the startup. Then, press CTRL+E to enter the test menu to check whether the SDRAM and flash memory are faulty. If so, dial Huawei customer service hotline and return the AC for repair. b. If not, dial Huawei customer service hotline or contact Huawei maintenance engineers to determine whether to upgrade the AC software or change other configurations. c. If the fault persists, contact Huawei technical support personnel.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top