What parameters need to be configured for an AP's plug-and-play mode

12

You only need to ensure that APs can discover the AC but do not need to configure parameters for Fit APs with zero configuration.

Other related questions:
What parameters are set to enable plug and play on Huawei APs
No parameter is set to enable the plug and play function on fit APs. You only have to ensure that fit APs can discover an AC.

Whether optical ports on the S1700 are plug-and-play
In normal conditions, an optical port on an S1700 switch starts to work immediately after an optical module is connected and does not require any configuration.

Are cards of S series switches hot swappable
Most of the cards of modular switches are hot swappable, and only the following cards are not: - S9300: subcards of LE0MFSUA, LE0D0VSTSA00, and LE0D0WMNPA00 - S7700: ES0D00FSUA00, ES02VSTSA, and LE0D0VSTSA00 - S9700: subcards of EH1D2VS08000 and EH1D2WM00000You can use Hardware Query Tool to query whether a card is hot swappable.

Which upgrade modes does an AP support
Currently, an AP can be upgraded using the AC, FTP, or SFTP. - AC loading: The target version file of the AP is saved on the AC. During loading, the AC sends the target version file to the AP using CAPWAP. - FTP loading: The target version file of the AP is saved on the FTP server. During loading, the AP logs in to the FTP server and obtains the target version file. - SFTP loading: The target version file of the AP is saved on the SFTP server. During loading, the AP logs in to the SFTP server and obtains the target version file. For information about how to configure AP upgrade modes, see "How do I configure an AP's upgrade mode."

How do I configure AP mode switching
An AP can switch between the Fat mode and Fit mode. APs in V200R003 or later support the Fat mode, and APs in different versions do not support mode switching. To switch a Fit AP in V200R002 to a Fat AP, first upgrade the Fit AP to V200R003. To switch a Fat AP to a Fit AP in V200R002, first switch the Fat AP to a Fit AP in V200R003, and then roll the Fit AP back to V200R002. Before configuring AP mode switching, run the upgrade upgrade-assistant-package command in the diagnostic view to upgrade the upgrade assistant package. The upgrade assistant package is not supported by the AD9430DN-24, AD9430DN-12, AP9130DN, AP8030DN, and AP8130DN. To switch a Fat AP to a Fit AP, perform the following operations: 1. Upload the system software package of a Fit AP to an FTP, SFTP, or TFTP server (taking the system software package AP6010DN_V200R005C00.bin and FTP server IP address 10.23.1.1 as an example). 2. Run the system-view command to enter the system view. (For the AP8030DN and AP8130DN, skip step 3 and go to step 4.) 3. Run the ap-mode-switch check command to check whether the file system allows a Fat AP to be switched to a Fit AP.. Note: If the check fails, do not perform the following steps. Otherwise, the AP's file system may be damaged, causing an AP startup failure. 4. Run the ap-mode-switch ftp AP6010DN_V200R005C00.bin 10.23.1.1 admin admin command to switch the system file of the Fat AP to that of the Fit AP using the FTP server. After the command is executed, the AP restarts and the mode switching is complete. To switch a Fit AP to a Fat AP, perform the following operations: 1. Upload the system software package of a Fat AP to an FTP, SFTP, or TFTP server (taking the system software package AP6010DN_V200R005C00.bin and FTP server IP address 10.23.1.1 as an example). 2. Run the system-view command to enter the system view. (For the AP8030DN and AP8130DN, skip steps 3 and 4, and go to step 5.) 3. Run the ap-mode-switch prepare command to change the file system status to allow a Fit AP to be switched to a Fat AP. 4. Run the ap-mode-switch check command to check whether the file system allows a Fit AP to be switched to a Fat AP. Note: If the check fails, do not perform the following steps. Otherwise, the AP's file system may be damaged, causing an AP startup failure. 5. Run the ap-mode-switch ftp AP6010DN_V200R005C00.bin 10.23.1.1 admin admin command to switch the system file of the Fit AP to that of the Fat AP using the FTP server. After the command is executed, the AP restarts and the mode switching is complete. For more information, see "Fat AP Upgrade Guide" of the appropriate version. Taking V200R005C10SPC700 as an example, to switch the AP mode, see Switching a Fit AP to a Fat AP and Switching a Fat AP to a Fit AP in FAT AP V200R005C10SPC700

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top