How do I disable WLAN radios and service sets as scheduled

2

For V200R005, the configuration is as follows:

Configuration on an AC:

[Huawei]wlan

[HuaweiHuawei-wlan-view]auto-off service radio ap-id 0 radio-id 0 start-time 1:00:00 end-time 7:00:00 //Disable the radio.

[Huawei-wlan-view]auto-off service ess service-set id 0 start-time 01:00:00 end-time 07:00:00 //Disable the service set.



Configuration on a Fat AP:

[Huawei]wlan

[Huawei-wlan-view]auto-off service radio interface wlan-radio0/0/0 start-time 1:00:00 end-time 7:00:00

[Huawei-wlan-view]auto-off service ess service-set id 0 start-time 01:00:00 end-time 07:00:00



For V200R006, the configuration is as follows:

Configuration on an AC:

[Huawei]wlan

[Huawei-wlan-view]ap-id 1

[Huawei-wlan-ap-1]radio 0

[Huawei-wlan-radio-1/0]radio disable//Disable the radio.

[Huawei-wlan-radio-1/0]quit

[Huawei-wlan-ap-1]quit

[Huawei-wlan-view]vap-profile name vap1

[Huawei-wlan-vap-prof-vap1]auto-off service start-time 1:00:00 end-time 7:00:00 //Disable the VAP.



Configuration on a Fat AP:

[Huawei]wlan

[Huawei] interface wlan-radio 0/0/0

[Huawei-Wlan-Radio0/0/0]radio disable//Disable the radio.

[Huawei-Wlan-Radio0/0/0]quit

[Huawei-wlan-view]vap-profile name vap1

[Huawei-wlan-vap-prof-vap1]auto-off service start-time 1:00:00 end-time 7:00:00//Disable the VAP.

Other related questions:
How to disable an AC's radio calibration
To disable radio calibration, perform the following operations: 1. Run the system-view command to enter the system view. 2. Run the wlan command to enter the WLAN view. 3. Run the undo calibrate enable command to disable radio calibration.

WLAN service set
WLAN service set A wireless network consists of radio profiles and service sets. - A radio profile contains WMM (QoS) profiles. - A service set contains traffic and security profiles, SSIDs, and WLAN-ESS/WLAN-BSS interfaces (wireless air interfaces). Service VLANs must be configured on ACs. - The wireless air interface is the logical interface for APs to connect to a STA. Typically, the wireless air interface is configured to work in hybrid mode.

How to configure radio calibration on an AC
For information about how to configure radio calibration on an AC, see: Versions earlier than V200R006: Configuring Radio Calibration V200R006: Configuring Radio Calibration

How to disable the web function on WLAN devices
To disable the web function, you need to disable the HTTP server function on WLAN devices. Perform the following steps: [Huawei] undo http server enable For V200R005 and later versions, the HTTPS function is enabled by default. You must disable HTTPS after disabling the HTTP server function. [Huawei] undo http secure-server enable

Adjustment of working channels of WLAN radios
Manually adjust working channels of WLAN radios. [HUAWEI] wlan [HUAWEI-wlan-view] ap 0 radio 0 or radio-profile name r1 [HUAWEI-wlan-radio-0/0] channel-mode fixed [HUAWEI-wlan-radio-0/0] channel 20mhz 6 Restore to the default channel by running the channel 20mhz 1 command. 20mhz indicates that the channel bandwidth is 20 MHz, which can be set to 40 MHz, 80 MHz, or 160 MHz. Web platform: - Choose Configuration > WLAN Configuration/AP Management > Radio Profile, and change Channel mode to fixed. - On the WLAN Configuration page, select 2.4 GHz or 5 GHz in the radio configuration area. Select the radio profile, channel bandwidth, channel, and power level in fixed mode. (To modify information, delete the existing configurations first. Then add a new radio profile and configure the parameters as required.) To check the working channel, run the display actual channel-power command. The following non-overlapping channels are available in mainland China: -2.4 GHz: 1, 6, 11 -5 GHz: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Note: 1. If the channel mode is changed from auto to fixed, APs will run in a fixed channel. 2. After automatic calibration is complete, the calibrated channel will be recorded after you disable the automatic calibration function and change the channel mode to fixed. This is applicable to scenarios with multiple APs. 3. To enable automatic calibration, ensure that the channel mode is auto. Otherwise, change the channel mode to auto first. 4. For Fit APs, the configurations take effect only after being delivered. 5. HT40 is not recommended in 2.4 GHz.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top