How to enable the web function on WLAN devices

7

The procedure for enabling the web function on WLAN devices is similar. The AC is used as an example:
1. Log in to the AC through the console port or Telnet.
2. Configure the management IP address.
[AC6605] vlan 10
[AC6605-vlan10] quit
[AC6605] interface Vlanif 10 // Configure VLANIF 10 as the management interface.
[AC6605-Vlanif10] ip address 192.168.200.161 24 //Configure the IP address of the web platform.
[AC6605-Vlanif10] quit
[AC6605] interface gigabitethernet 0/0/1 //GE0/0/1 is the number of the physical interface that connects the AC and PC using the web platform to log in to the AC. Set this parameter based on network situations. 
[AC6605-GigabitEthernet0/0/1] port link-type trunk
[AC6605-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[AC6605-GigabitEthernet0/0/1] quit
3. Enable the HTTP or HTTPS service.
   - Enable the HTTP service.
   [AC6605] http server enable //The HTTP service is enabled by default.
   - Enable the HTTPS service.
   [AC6605] http secure-server enable //The HTTPS service is enabled by default.
4. Configure the web platform users.
[AC6605] aaa
[AC6605-aaa] local-user admin password irreversible-cipher Helloworld@6789
[AC6605-aaa] local-user admin privilege level 15
[AC6605-aaa] local-user admin service-type http
[AC6605-aaa] quit
5. Log in to the web platform.
Open the web browser on your PC, and enter http://192.168.200.161 (IP address configured in Step 2) in the address box. Press Enter. The web platform login page is displayed.

Other related questions:
How to disable the web function on WLAN devices
To disable the web function, you need to disable the HTTP server function on WLAN devices. Perform the following steps: [Huawei] undo http server enable For V200R005 and later versions, the HTTPS function is enabled by default. You must disable HTTPS after disabling the HTTP server function. [Huawei] undo http secure-server enable

How to enable the Telnet server function for a WLAN device
By default, the Telnet server function is enabled for WLAN devices of V200R003 and earlier versions and disabled for WLAN devices of V200R005 and later versions. Run the telnet server enable command to enable the Telnet server function. For a Fit AP, if it has gone online on an AC, run the telnet enable command in the AP profile view of the AC to enable the Telnet service for this Fit AP.

How to change the web password of WLAN devices
To change the web password of WLAN devices, perform the following steps: If the web login password is lost or you want to change the existing web login password, you can log in to the device using other methods, such as the console port or Telnet, and set the password again. 1. Log in to the device using other methods, such as the console port. 2. Change the user password. The following command output is an example that sets the user name to huawei and the new password to Huawei@123 in AAA authentication: [Huawei] aaa [Huawei-aaa] local-user huawei password irreversible-cipher Huawei@123 [Huawei-aaa] local-user huawei service-type http //Set the access type of huawei to HTTP. [Huawei-aaa] local-user huawei privilege level 15

How to enable the web function on an AR router
The methods of enabling the web function on an AR router are as follows: Method 1: Default web login 1. Connect a PC to the router over the management interface through a network cable. 2. Configure an IP address for the PC. Configurable network segment: 192.168.1.2~192.168.1.254. 3. Open a browser, enter the URL "https://192.168.1.1" in the address bar, and click Enter to enter the user login page. 4. Enter login information. 5. Configure the router through the web NMS page. Note: If you cannot enter the web NMS page, the software version you use does not support the default web login method. Please try the following method: Method 2: Non-default web login 1. Connect a PC to the router over the CON/AUX interface through a console configuration cable. 2. Enable the terminal emulation software on the PC, create a connection, and set an interface for the connection and other communication parameters. 3. Press Enter until the following information is displayed to remind users of configuring a verification code. 4. Connect a PC to the router over the management interface through a network cable. 5. Configure an IP address for the router for management. 6. Enable the web service. 7. Configure an HTTPS user and a user level. 8. Configure an IP address for the PC. 9. Open a browser, enter the URL "https://192.168.1.1" in the address bar, and click Enter to enter the user login page. 10. Configure the router through the web NMS page.

How to enable DHCP snooping on a WLAN device
DHCP snooping is a DHCP security feature. To configure DHCP snooping security functions, enable DHCP snooping first. For ACs, you must enable DHCP snooping in the system view and then on an interface or in a VLAN. The operations are as follows: 1. Run the dhcp snooping enable [ ipv4 | ipv6 ] command in the system view to enable DHCP snooping globally. 2. Enable DHCP snooping in the system view, interface view, or VLAN view. - Run the dhcp snooping enable vlan { vlan-id1 [ to vlan-id2 ] } &<1-10> command to enable DHCP snooping. - Run the vlan vlan-id command to enter the VLAN view, or run the interface interface-type interface-number command to enter the interface view. - Run the dhcp snooping enable command to enable DHCP snooping on the interface or in the VLAN. DHCP snooping is enabled on Fat APs by default.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top