How to improve an AP's anti-interference capability

8

APs use the following methods to prevent interference:

- Automatically adjust channels.

- Multiplex channels.

- Adjust packet transmission rates.

- Packet-based power control (supported by only Fit APs)

- Intelligent load balancing (supported by only Fit APs)

Other related questions:
Introduction to OceanStor 9000 high-performance access
OceanStor 9000 provides high-performance service access capabilities, and uses key technologies, such as global cache, high-speed interconnection, concurrent access, and SSD acceleration. OceanStor 9000 provides high-bandwidth, low-latency, and high-concurrency service access capabilities. OceanStor 9000 performance increases linearly as the number of nodes increases, meeting requirements for high-performance applications.

How to detect interference on WLAN networks
You can use Wirelessmon, NetStumbler, or InSSIDer (downloaded for free on the Internet) to check whether there is strong co-channel or adjacent-channel interference near the AP. In general, the interference signal strength should be lower than �?0 dBm. If multiple co-channel or adjacent-channel interference signals exist and the strength is strong, perform network optimization to prevent channel conflicts. If interference sources cannot be determined using a scanning tool, - Check whether wireless devices such as Bluetooth devices, infrared devices, and microwave ovens exist, because non-WLAN devices may cause severe interference to WLAN networks. - Use the interference detection function to further determine the interference source. Radio channels are often affected by the radio environment, and the service quality is therefore degraded. Interference detection allows APs to send alarms to an AC when co-channel, adjacent-channel, or STA interference exceeds the alarm threshold. Interference detection can detect AP co-channel interference, AP adjacent-channel interference, and STA interference. AP co-channel interference: Two APs working at the same frequency band interfere with each other. For example, on a large-scale WLAN (a university campus network), different APs often use work in the same channel. When coverage areas of the APs overlap, co-channel interference exists, degrading network performance. AP adjacent-channel interference: Two APs with different center frequencies have overlapping areas, resulting in adjacent-channel interference. Therefore, if APs are placed too close to each other or they have strong signals, bigger noise will be produced, degrading network performance. STA interference: If there are many STAs that are managed by other APs around an AP, services of the STAs managed by the local AP may be affected. The following are alarms for co-channel interference and STA interference. V200R005C10: WLAN/4/AP_COMMON_FREQUENCY_DISTURB: OID [oid] The co-channel interference exceeds the alarm threshold. (APID=[INTEGER], APID=[INTEGER], RadioID=[INTEGER], APMAC=[OPAQUE], APChannel=[INTEGER], BssId=[OPAQUE], RSSI threshold percent=[INTEGER])//AP_COMMON_FREQUENCY_DISTURB indicates that co-channel interference exists. WLAN/4/STATION_DISTURB: OID [oid] Jam of station is detected notify.(APID=[INTEGER], APID=[INTEGER], RadioID=[INTEGER], APMAC=[OPAQUE], APChannel=[INTEGER], StatMACList=[STRING])//STATION_DISTURB indicates that STA interference exists. V200R006: WLAN/4/AP_COMMON_FREQUENCY_DISTURB: OID [oid] The co-channel interference exceeds the alarm threshold.(APMAC=[OPAQUE], RadioID=[INTEGER], ApName=[OCTET], APChannel=[INTEGER], BssId=[OPAQUE], RSSI threshold percent=[INTEGER]%, APID=[INTEGER])//AP_COMMON_FREQUENCY_DISTURB indicates that co-channel interference exists. WLAN/4/STATION_DISTURB: OID [oid] Jam of station is detected notify.(APMAC=[OPAQUE], RadioID=[INTEGER], ApName=[OCTET], APChannel=[INTEGER], StatMACList=[STRING], APID=[INTEGER])//STATION_DISTURB indicates that STA interference exists.

Influence of co-channel interference on APs
Co-channel interface is a major factor that reduces an AP's maximum throughput. When APs are densely deployed, their signals have a large overlapping coverage area, resulting in severe co-channel interference. In this case, the APs' maximum throughput decreases greatly.

Preventing signal interference by setting the signal strength of APs
To prevent signal interference, adjust APs' transmit power and increase APs' deployment intervals. You can also use directional antennas and smart antennas to control signal coverage areas and prevent interference.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top