How to disable an AC's radio calibration

8

To disable radio calibration, perform the following operations:

1. Run the system-view command to enter the system view.

2. Run the wlan command to enter the WLAN view.

3. Run the undo calibrate enable command to disable radio calibration.

Other related questions:
How to configure radio calibration on an AC
For information about how to configure radio calibration on an AC, see: Versions earlier than V200R006: Configuring Radio Calibration V200R006: Configuring Radio Calibration

Do APs support radio calibration
All Huawei APs support radio calibration. Currently, 80 MHz calibration bandwidth is supported by the AP2030DN, AP3030DN, AP4030DN, AP4030DN-E, AP4130DN, AP5030DN, AP5030DN-S, AP5130DN, AP7030DE, AP9131DN, AP9132DN, AD9430DN-24 (including the mapping RUs), AD9430DN-12(including the mapping RUs), AP9330DN, AP8030DN, and AP8130DN.

How do I disable WLAN radios and service sets as scheduled
For V200R005, the configuration is as follows: Configuration on an AC: [Huawei]wlan [HuaweiHuawei-wlan-view]auto-off service radio ap-id 0 radio-id 0 start-time 1:00:00 end-time 7:00:00 //Disable the radio. [Huawei-wlan-view]auto-off service ess service-set id 0 start-time 01:00:00 end-time 07:00:00 //Disable the service set. Configuration on a Fat AP: [Huawei]wlan [Huawei-wlan-view]auto-off service radio interface wlan-radio0/0/0 start-time 1:00:00 end-time 7:00:00 [Huawei-wlan-view]auto-off service ess service-set id 0 start-time 01:00:00 end-time 07:00:00 For V200R006, the configuration is as follows: Configuration on an AC: [Huawei]wlan [Huawei-wlan-view]ap-id 1 [Huawei-wlan-ap-1]radio 0 [Huawei-wlan-radio-1/0]radio disable//Disable the radio. [Huawei-wlan-radio-1/0]quit [Huawei-wlan-ap-1]quit [Huawei-wlan-view]vap-profile name vap1 [Huawei-wlan-vap-prof-vap1]auto-off service start-time 1:00:00 end-time 7:00:00 //Disable the VAP. Configuration on a Fat AP: [Huawei]wlan [Huawei] interface wlan-radio 0/0/0 [Huawei-Wlan-Radio0/0/0]radio disable//Disable the radio. [Huawei-Wlan-Radio0/0/0]quit [Huawei-wlan-view]vap-profile name vap1 [Huawei-wlan-vap-prof-vap1]auto-off service start-time 1:00:00 end-time 7:00:00//Disable the VAP.

How to disable the Telnet server function for a WLAN device
By default, the Telnet server function is enabled for WLAN devices of V200R003 and earlier versions and disabled for WLAN devices of V200R005 and later versions. Run the undo telnet server enable command to disable the Telnet server function. For a Fit AP, if it has gone online on an AC, run the telnet disable command in the AP profile view of the AC to disable the Telnet service for this Fit AP.

Why does an AC fail to report unauthorized APs after calibration is enabled
The possible causes are: - Unauthorized AP detection is not enabled when calibration is enabled on the AC. - After the calibration command is executed, the AC does not send neighbor detection messages to APs. - APs do not receive neighbor detection messages from the AC. - APs are not enabled to detect neighbors. - APs do not report detected information to the AC. - The AC does not receive neighbor information sent from APs. - Errors occur when the AC is saving received neighbor information.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top