What is a fractional channelized board

2

Currently, the fractional channelized board refers to the 1E1T1-F/2E1T1-F/4E1T1-F/8E1T1-F board.

The 1E1T1-F/2E1T1-F/4E1T1-F/8E1T1-F board line contains 32 timeslots that are numbered from 0 to 31. In fractional channelized mode, timeslot 0 is used to transmit synchronous information, and other timeslots can be bundled into a channel set.

Other related questions:
Adjacent channel isolation for the M40 board
For the M40 board, the adjacent channel isolation should be greater than 22 dB.

Adjacent channel isolation for the D40 board
For the D40 board, the adjacent channel isolation should be greater than 25 dB.

Types of channel bandwidth supported by OSC boards
In general, OSC boards support the following channel bandwidth: 4.096 Mbit/s, 16.896 Mbit/s, and 155.52 Mbit/s.

Differences between timeslot allocation modes of the ClientLP ports on TOM boards on OSN 6800 devices and related precautions
Question: The current product manuals and configuration manuals for OSN 6800 devices do not describe timeslot configuration for TOM boards. When timeslots are incorrectly configured, services will fail to be provisioned, or abnormal alarms will be reported, which also causes the failure to provision services. Why? Analysis: The service type configuration sequence for channels on the ClientLP port is associated with the automatic timeslot allocation mode. Answer: Timeslots of TOM boards can be automatically or manually allocated. The automatic timeslot allocation mode is used by default. You can change the allocation mode in the WDM timeslot configuration window. 1. In automatic allocation mode, timeslots are automatically allocated based on the channel service type configured for the logical port ClientLP on TOM boards. The TOM boards, whose service types are first configured, will be first allocated with timeslot channels with channel numbers sorted in ascending order. In the non-cascading mode, each ClientLP port of a TOM board is allocated with 16 timeslots. For example, if the GE service is first configured for the ClientLP1-1 port and then the STM-4 service is configured for the ClientLP1-2 port, channels 1 to 7 (transmit and receive timeslots) will be automatically allocated for the ClientLP1-1 port in the WDM timeslot configuration window, and channels 5 to 8 will be allocated for the ClientLP1-2 port. Reversely, if the STM-4 service is first configured for the ClientLP1-2 port and then the GE service is configured for the ClientLP1-1 port, timeslots 1 to 4 will be allocated for the ClientLP1-2 port and 5 to 11 will be allocated for the ClientLP1-1 port. The numbers of transmit and receive timeslots are consistent. 2. In automatic mode, pay attention to the timeslot mapping between the service adding and dropping ends. The incorrect service type setting sequence may cause an incorrect association between timeslots at two ends and also a failure to provision services. 3. In manual mode, the transmit and receive timeslot numbers are manually configured for ClientLP ports. The number of timeslots must be consistent with service types. For example, the STM-16 service occupies 16 timeslots, the GE service occupies seven timeslots, and the STM-4 service occupies four timeslots. The transmit and receive timeslots at the ports can be inconsistent, but the transmit and receive timeslots at the adding and dropping ends of a service must be consistent. 4. If no service type is configured for a ClientLP port channel, the channel will not be displayed in the timeslot configuration window. If no service type is configured for all channels at a ClientLP port, the port cannot be selected in ODU1 cross-connection configuration. Suggestion and conclusion: You should understand the timeslot allocation rules for channels on TOM boards, preventing the failure to provision services when timeslots are incorrectly configured.

Whether the channel diagram can indicate the usage of WDM board channels
Yes. The channel diagram shows the usage of board channels in different colors. A channel in gray is not used yet and a channel in green has services configured.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top