Why is a VAP created

4

VAPs are created to provide different services through different parameter settings, such as security policies, traffic scheduling, and virtual interfaces.

Other related questions:
What is the purpose of creating VAPs on a WLAN device
A VAP is created to provide different services, including parameter settings such as security, traffic, and interfaces.

What is the maximum number of VAPs that can be created on an AC
V200R003C00: - The AC6605 supports a maximum of 4096 VAPs. - The AC6005 supports a maximum of 2048 VAPs. V200R005 and later versions: - The AC6605 supports a maximum of 16384 VAPs. - The AC6005 supports a maximum of 16384 VAPs. - The ACU2 supports a maximum of 16384 VAPs.

What is the function of an AP region
An AP region is a geographical scope in which APs are deployed. It is used for radio power adjustment to reduce interference or batch upgrade of APs of the same model in the same region. AP regions can be added, deleted, modified, and merged.

Configure basic services of the Fat AP on the AR
You can configure the Fat AP service to enable users to easily access a wireless network and move around within the coverage of the wireless network. The procedure for configuring the basic function of the Fat AP is as follows: 1. Configure the WLAN mode of the device, basic parameters of the AP, and the addresses allocated to STAs. 2. Configure WLAN service VAPs. After APs go online, you can configure service VAPs for the APs to provide differentiated WLAN services for users. The detailed configuration is as follows: Create a WMM profile and a radio profile, bind the WMM profile to the radio profile, create a security profile and a traffic profile, configure a WLAN-BSS interface and a WLAN service set, bind the WLAN-BSS interface, security profile, and traffic profile to the WLAN service set, configure a radio, and bind the radio profile and VAP to the radio. For details, see Example for Configuring Wireless User Access to a WLAN.

What STA information can be displayed on a WLAN device
1. Number of STAs associated with an AP For V200R005, run the display station assoc-num command. For V200R006, run the display station ap-id xx command. 2. STA information For V200R005, run the display station assoc-info sta sta-mac command. For V200R006, run the display station sta-mac sta-mac command. The display contents vary depending on versions. The following uses V200R005C10 as an example: display station assoc-info sta d420-6df4-f37e Station mac-address : d420-6df4-f37e //STA mac Station ip-address : 0.0.0.0 //STA IP Station gateway : 0.0.0.0 Associated SSID : jsldoc //SSID Station online time(ddd:hh:mm:ss) : 000:00:04:20 //Online time The upstream SNR(dB) : 30.0 The upstream aggregate receive power(dBm) : -79.0 Station connect rate(Mbps) : 23 //Rate Station connect channel : 1 //Channel Station inactivity time(ddd:hh:mm:ss) : 000:00:00:00 ...... Station's RSSI(dBm) : -66 //Single strength Station's Noise(dBm) : -109 Station's radio mode : 11b //Network type Station's AP ID : 6 //AP ID (supported only by V200R005C00) Station's Radio ID : 0 //0 indicates 2.4G, and 1 indicates 5G (supported only by V200R005C00). Station's Authentication Method : OPEN Station's Cipher Type : NO CIPHER Station's User Name : d4206df4f37e Station's Vlan ID : 28 Station's Channel Band-width : 20MHz Station's asso BSSID : dcd2-fc9a-2110 Station's state : Asso with auth Station's Qos Mode : NULL Station's HT Mode : - Station's MCS value : 0 Station's NSS value : 0 Station's Short GI : support Station's roam state : No

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top