How can I set alarm severity on a WLAN device

4

To set alarm severity on a WLAN device, run the alarm-name alarm-name severity severity command in the alarm management view.

Run the undo alarm-name severity command to restore the alarm severity to the default setting.

Other related questions:
How can I clear alarms on a WLAN device
To clear alarms on a WLAN device, run the clear alarm active { all | sequence-number sequence-number } command in the alarm management view.

How to configure the WEP security policy on WLAN devices
For V200R003 and V200R005, you can perform the following steps on ACs or Fat APs to configure the WEP security policy: 1. Run the security-profile { id profile-id | name profile-name } * command in the WLAN view to display the security profile view. The variable profile-id specifies the ID of a security profile, and profile-name specifies the name of the security profile. 2. Run the security-policy wep command in the security profile view to set the security policy to WEP. By default, the security policy is WEP. By default, WEP uses open system authentication and non-encryption. The default configuration has security risks, so you are advised to configure the Portal security policy or use WPA/WPA2 authentication. 3. Configure the authentication and encryption modes: - Configure open system authentication + non-encryption: a. Run the wep authentication-method open-system [ data-encrypt ] command in the security profile view to configure WEP open system authentication. b. The variable data-encrypt indicates open system authentication and WEP encryption. In this case, you must run the wep key command and the wep default-key command to set the WEP shared key, which is used for generating the encryption key to encrypt WLAN data packets. - Configure the shared key authentication + WEP encryption: a. Run the wep authentication-method share-key command in the security profile view to configure WEP shared key authentication. b. Run the wep key { wep-40 | wep-104 | wep-128 } { pass-phrase | hex } key-id cipher cipher-key-value command in the security profile view to configure the WEP shared key and key ID. The variable key-id specifies the key ID, and cipher-key-value specifies the password in cipher text. c. Run the wep default-key key-id command in the security profile view to set the key ID of the WEP shared key. The variable key-id specifies the default key ID. A maximum of four WEP keys can be configured, and only one WEP key is valid at a time. 4. Run the commit { all | ap ap-id } command in the WLAN view to deliver configurations to the APs (applicable only to the AC). The variable ap-id specifies the AP ID.

How to configure channels and power for WLAN devices
Configure radio channels and power for WLAN devices manually or by configuring radio calibration. -Manual configuration Take the configuration on the AC as an example. Users can adjust the channel and power using the channel 20mhz xx and power-level commands. [AC6005-wlan-radio-0/0]display this # radio-profile id 0 channel 20MHz 13 power-level 2 # return Configure channels and power for Fat AP devices in the radio interface view.

How do I query alarms on a WLAN device
When a WLAN device becomes faulty or works abnormally because the environment does not meet operation requirements, the system generates alarms based on fault types and relevant logs. WLAN product documentation describes alarm description, alarm attributes, alarm parameters, impact on the system, possible causes, and solutions of each feature on a WLAN device. The following tips will help you quickly find reference information about a specific alarm: - An alarm ID uniquely identifies an alarm and allows you to search an alarm by alarm ID for its description and handling procedure. - Alarms that have the same ID but are triggered by different causes are identified by error code (for example, BaseTrapProbableCause). You can search for error codes in the Alarm Reference. - Do not search an alarm based on information carrying a variable, such as the alarm generation time, port number, process ID, or device name. To query a WLAN alarm, perform the following operations: - Query by keyword Log in to and enter a keyword, such as "AP online alarm". You can also obtain the required product documentation and query related alarms. - Query in the product documentation 1. Log in to . 2. Choose Enterprise Network > WLAN. 3. Select a WLAN device model. On the page that is displayed, select the product documentation of the specific version. 4. Query alarms online or download the product documentation for alarm query.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top