Detailed information about outdoor AP antennas

25

For detailed information about AP antennas, see HUAWEI Access Points Antenna Quick Start.

Other related questions:
Types of Huawei antennas
Indoor antenna: - Indoor omnidirectional/directional ceiling-mounted antenna - Indoor directional antenna - Indoor SMA antenna Outdoor antenna: - 2.4G&5G outdoor omnidirectional antenna - 2.4G&5G outdoor directional antenna - Outdoor backhaul antenna

How to select antennas for APs
Antennas receive and send radio signals. Select antennas for APS by referring to HUAWEI Access Points Antenna Quick Start. Contact Huawei local offices to purchase antennas. Antennas from other vendors are not recommended for working with Huawei APs. Consider the following points when selecting antennas: 1. Usage scenario and purpose Indoor antennas are generally used to provide signal coverage in indoor scenarios while outdoor antennas are used to provide signal coverage and bridging backhaul in outdoor scenarios. 2. Local standards and regulations The transmit power and maximum gain of antennas must strictly comply with local standards and regulations. 3. Shape and distance of the coverage or backhaul area - Coverage: Directional antennas are recommended in long and narrow areas while omnidirectional antennas are recommended in round and square areas. - Backhaul: Directional antennas are usually used. If the backhaul distance is long, use high-gain antennas; if backhaul targets are concentrated, use small-angle antennas. 4. Signal transmission band (2.4 GHz/5 GHz) - Coverage: To provide 2.4 GHz and 5 GHz signal coverage, use 2.4Gand 5G antennas in the same area or use dual-band antennas. - Backhaul: Only 5 GHz antennas are used for backhaul.

What STA information can be displayed on a WLAN device
1. Number of STAs associated with an AP For V200R005, run the display station assoc-num command. For V200R006, run the display station ap-id xx command. 2. STA information For V200R005, run the display station assoc-info sta sta-mac command. For V200R006, run the display station sta-mac sta-mac command. The display contents vary depending on versions. The following uses V200R005C10 as an example: display station assoc-info sta d420-6df4-f37e Station mac-address : d420-6df4-f37e //STA mac Station ip-address : 0.0.0.0 //STA IP Station gateway : 0.0.0.0 Associated SSID : jsldoc //SSID Station online time(ddd:hh:mm:ss) : 000:00:04:20 //Online time The upstream SNR(dB) : 30.0 The upstream aggregate receive power(dBm) : -79.0 Station connect rate(Mbps) : 23 //Rate Station connect channel : 1 //Channel Station inactivity time(ddd:hh:mm:ss) : 000:00:00:00 ...... Station's RSSI(dBm) : -66 //Single strength Station's Noise(dBm) : -109 Station's radio mode : 11b //Network type Station's AP ID : 6 //AP ID (supported only by V200R005C00) Station's Radio ID : 0 //0 indicates 2.4G, and 1 indicates 5G (supported only by V200R005C00). Station's Authentication Method : OPEN Station's Cipher Type : NO CIPHER Station's User Name : d4206df4f37e Station's Vlan ID : 28 Station's Channel Band-width : 20MHz Station's asso BSSID : dcd2-fc9a-2110 Station's state : Asso with auth Station's Qos Mode : NULL Station's HT Mode : - Station's MCS value : 0 Station's NSS value : 0 Station's Short GI : support Station's roam state : No

How do I view information about the AP with which a STA associates
To display information about the AP with which a STA associates, run the following command: display access-user mac-address x-x-x The following information including the AP ID is displayed: Basic: User ID : 365 User name : e005c5fab829 Domain-name : default User MAC : e005-c5fa-b829 //MAC address of the user User IP address : 192.168.130.254 //IP address of the user User access Interface : Wlan-Dbss1:0 QinQVlan/UserVlan : 0/130 //User VLAN User access time : 2013/03/06 19:52:29 User accounting session ID : AC66050000000000013066b6c7000365 User access type : WEB Terminal Device Type : Data Terminal AP ID : 0 //ID of the connected AP AP name : ap-0 Radio ID : 0 //Access frequency band: 0 indicates 2.4G, and 1 indicates 5G. AP MAC : 0046-4b74-68c0 //AP mac SSID : test //SSID name Online time : 59(s)

How to view detailed information about 802.1x authentication users on S series switches
For S series switches (except the S1700), you can perform the following operations in any view to check detailed information about online 802.1x authentication users. - In NAC common mode (applicable to switches running all versions): [HUAWEI] display access-user //Obtain indexes of 802.1x authentication users based on the users' MAC or IP addresses. [HUAWEI] display access-user user-id 1 //Check information about the users based on their indexes. - In NAC unified mode (applicable to switches running V200R005C00 and later versions): [HUAWEI] display access-user access-type dot1x //Check information about online 802.1x authentication users. [HUAWEI] display access-user user-id 1 //You can also run the display access-user username user-name detail command on switches running V200R007C00 and later versions to check detailed information about 802.1x authentication users.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top