Example for Configuring Multicast Suppression in Tunnel Forwarding Mode

26

Example for Configuring Multicast Packet Suppression in Tunnel Forwarding Mode
In V200R005, the configuration procedure is as follows:
Create the traffic classifier test and define a matching rule.
<AC6605>system-view
[AC6605]traffic classifier test
[AC6605-classifier-test]if-match destination-mac 0100-5e00-0000 mac-address-mask ffff-ff00-0000 //Match the destination MAC address of multicast packets.
[AC6605-classifier-test]quit
Create the traffic behavior test, enable traffic statistics collection, and set the traffic rate limit.
[AC6605]traffic behavior test
[AC6605-behavior-test]statistic enable
[AC6605-behavior-test]car cir 100 //Set the rate limit to 100 kbit/s. If multicast services are available, you are advised to set the rate limit according to the service traffic.
[AC6605-behavior-test]quit
Create the traffic policy test and bind the traffic classifier and traffic behavior to the traffic policy.
[AC6605]traffic policy test
[AC6605-trafficpolicy-test]classifier test behavior test
[AC6605-trafficpolicy-test]quit
Apply the traffic policy to inbound or outbound directions of interfaces.
[AC6605]interface wlan-ess 1
[AC6605-Wlan-Ess1]traffic-policy test inbound
[AC6605-Wlan-Ess1]traffic-policy test outbound
[AC6605-Wlan-Ess1]quit
In V200R006 and later versions, the configuration procedure is as follows:
Create the traffic profile test and set the maximum traffic volume of multicast packets in the profile.
<AC6605>system-view
[AC6605]wlan
[AC6605-wlan-view]traffic-profile name test
[AC6605-wlan-traffic-prof-test]traffic-optimize multicast-suppression packets 100//Set the maximum traffic volume of multicast packets to 100 pps. If multicast services are available, you are advised to set the rate limit according to the service traffic.
[AC6605-wlan-traffic-prof-test]quit
Bind the traffic profile to the VAP profile.
[AC6605-wlan-view]vap-profile name test
[AC6605-wlan-vap-prof-test]traffic-profile test
[AC6605-wlan-vap-prof-test]quit

Other related questions:
Example for Configuring Multicast Packet Suppression In Direct Forwarding Mode
Example for Configuring Multicast Packet Suppression In Direct Forwarding Mode
Create the traffic classifier test and define a matching rule.
<huawei>system-view
[HUAWEI] sysname SwitchA
[SwitchA] traffic classifier test
[SwitchA-classifier-test] if-match destination-mac 0100-5e00-0000 mac-address-mask ffff-ff00-0000 //Match the destination MAC address of multicast packets.
[SwitchA-classifier-test] quit
Create the traffic behavior test, enable traffic statistics collection, and set the traffic rate limit.
[SwitchA] traffic behavior test
[SwitchA-behavior-test]statistic enable
[SwitchA-behavior-test]car cir 100   //Set the rate limit to 100 kbit/s. If multicast services are available, you are advised to set the rate limit according to the service traffic.
[SwitchA-behavior-test]quit
Create the traffic policy test and bind the traffic classifier and traffic behavior to the traffic policy.
[SwitchA]traffic policy test
[SwitchA-trafficpolicy-test]classifier test behavior test
[SwitchA-trafficpolicy-test]quit
Apply the traffic policy to inbound or outbound directions of interfaces.
[SwitchA]interface gigabitethernet 0/0/1
[SwitchA-GigabitEthernet0/0/1]traffic-policy test inbound
[SwitchA-GigabitEthernet0/0/1]traffic-policy test outbound
[SwitchA-GigabitEthernet0/0/1]quit

What are the differences in AP-side switch interface configuration and intermediate switch configuration in direct and tunnel forwarding modes
#NAME?

Default Layer 2 multicast forwarding mode on an S series switch
For S series switches excluding the S1700, after Layer 2 multicast is enabled, the S1720, S2710SI, S2700SI, S2700EI, S2720EI, S2750EI, S5700LI, and S5700S-LI (S5700S-28X-LI-AC and S5700S-52X-LI-AC) forward multicast data based on MAC addresses, and other models forward multicast data based on IP addresses by default.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top