How to configure interface mirroring on AR routers

1

By configuring local interface mirroring (one mirroring interface or multiple mirroring interfaces), you can replicate the packets transmitted through the interface to local monitoring devices for analysis and surveillance.
Note:
Interfaces used in the example are just for reference. Configure local interface mirroring based on actual interface information in practice.
Before configuring local interface mirroring, ensure that the link protocol state of the interface is Up.
In the configuration commands, inbound indicates the inbound mirroring traffic and outbound indicates the outbound mirroring traffic. You can change outbound to inbound in the commands if you need outgoing mirroring traffic.

Scenario 1: Configure local interface mirroring (one mirroring interface)
(1)Configure the observing interface
#Configure GE0/0/1 as the local observing interface on the router.
system-view
[Huawei] observe-port interface gigabitethernet 0/0/1
(2)Configure the mirroring interface
#Configure GE0/0/2 as the mirroring interface, and bind the inbound mirroring traffic to the local observing interface, that is, replicate the packets received by the mirroring interface to the local observing interface.
[Huawei] interface gigabitethernet 0/0/2
[Huawei-GigabitEthernet0/0/2] mirror to observe-port inbound
[Huawei-GigabitEthernet0/0/2] return

For details, select Configuration > CLI-based Configuration > Network Management and Monitoring Configuration Guide >
Mirroring Configuration > Configuration Examples > Example for Configuring 1:1 Local Port Mirroring in the following URL: [http://support.huawei.com/hedex/hdx.do?docid=EDOC1000116356&id=dc_cfg_mirror_1131&text=Example%2520for%2520Configuring%25201%253A1%2520Local%2520Port%2520Mirroring&lang=en">Product Documentation.

Scenario 2: Configure local interface mirroring (multiple mirroring interfaces)
(1)Configure the observing interface
#Configure Eth0/0/1 as the local observing interface on the router.
system-view
[Huawei] observe-port interface ethernet 0/0/1
(2)Configure the mirroring interface.
Configure Eth0/0/0 as the mirroring interface on the router.
[Huawei] interface ethernet 0/0/0
[Huawei-Ethernet0/0/0] mirror to observe-port inbound
[Huawei-Ethernet0/0/0] quit
# Configure Eth0/0/2 as the mirroring interface on the router.
[Huawei] interface ethernet 0/0/2
[Huawei-Ethernet0/0/2] mirror to observe-port inbound
[Huawei-Ethernet0/0/2] return

For details, select Configuration > CLI-based Configuration > Network Management and Monitoring Configuration Guide >
Mirroring Configuration > Configuration Examples > Example for Configuring N:1 Local Port Mirroring in the following URL: Product Documentation.

Other related questions:
How to configure interface mirroring on AR routers
By configuring local interface mirroring (one mirroring interface or multiple mirroring interfaces), you can replicate the packets transmitted through the interface to local monitoring devices for analysis and surveillance.
Note:
Interfaces used in the example are just for reference. Configure local interface mirroring based on actual interface information in practice.
Before configuring local interface mirroring, ensure that the link protocol state of the interface is Up.
In the configuration commands, inbound indicates the inbound mirroring traffic and outbound indicates the outbound mirroring traffic. You can change outbound to inbound in the commands if you need outgoing mirroring traffic.

Scenario 1: Configure local interface mirroring (one mirroring interface)
(1)Configure the observing interface
#Configure GE0/0/1 as the local observing interface on the router.
system-view
[Huawei] observe-port interface gigabitethernet 0/0/1
(2)Configure the mirroring interface
#Configure GE0/0/2 as the mirroring interface, and bind the inbound mirroring traffic to the local observing interface, that is, replicate the packets received by the mirroring interface to the local observing interface.
[Huawei] interface gigabitethernet 0/0/2
[Huawei-GigabitEthernet0/0/2] mirror to observe-port inbound
[Huawei-GigabitEthernet0/0/2] return

For details, select Configuration > CLI-based Configuration > Network Management and Monitoring Configuration Guide >
Mirroring Configuration > Configuration Examples > Example for Configuring 1:1 Local Port Mirroring in the following URL: [http://support.huawei.com/hedex/hdx.do?docid=EDOC1000116356&id=dc_cfg_mirror_1131&text=Example%2520for%2520Configuring%25201%253A1%2520Local%2520Port%2520Mirroring&lang=en">Product Documentation.

Scenario 2: Configure local interface mirroring (multiple mirroring interfaces)
(1)Configure the observing interface
#Configure Eth0/0/1 as the local observing interface on the router.
system-view
[Huawei] observe-port interface ethernet 0/0/1
(2)Configure the mirroring interface.
Configure Eth0/0/0 as the mirroring interface on the router.
[Huawei] interface ethernet 0/0/0
[Huawei-Ethernet0/0/0] mirror to observe-port inbound
[Huawei-Ethernet0/0/0] quit
# Configure Eth0/0/2 as the mirroring interface on the router.
[Huawei] interface ethernet 0/0/2
[Huawei-Ethernet0/0/2] mirror to observe-port inbound
[Huawei-Ethernet0/0/2] return

For details, select Configuration > CLI-based Configuration > Network Management and Monitoring Configuration Guide >
Mirroring Configuration > Configuration Examples > Example for Configuring N:1 Local Port Mirroring in the following URL: Product Documentation.

How to configure remote interface mirroring on AR series routers
Remote interface mirroring is only supported in V200R005C32 and earlier versions. By configuring remote interface mirroring, you can replicate the packets transmitted through the interface to remote monitoring devices for analysis and surveillance. Before configuring remote interface mirroring, ensure that the routing protocol and GRE tunnels are configured. 1. Configure the remote observing server. Procedure Run the system-view command to enter the system view. Run the observe-server destination-ip destination-ip-address source-ip source-ip-address [ dscp dscp-value ] command to configure the observing server in remote interface mirroring. Note: The destination-ip-address parameter indicates the IP address of the monitoring device. The source-ip-address parameter indicates the IP address of the mirroring interface. If the IP addresses of the monitoring device and the mirroring interface are private IP addresses, GRE tunnels must be configured first to ensure the interworking between private IP addresses on public networks. 2. Configure the remote mirroring interface. Background A mirroring interface can be an IP-Trunk interface, an Ethernet interface, or an Eth-Trunk interface. - If an Eth-trunk interface is configured as a mirroring interface, a member interface of the Eth-trunk interface cannot be configured as a mirroring interface separately. If you want to configure a member interface of the Eth-trunk as a mirroring interface, you must unbind the member interface from the Eth-trunk interface. - If a member interface of an Eth-trunk is configured as a mirroring interface, the Eth-trunk interface cannot be configured as a mirroring interface. If you want to configure the Eth-trunk interface as a mirroring interface, you must unbind the member interface that is configured as the mirroring interface from the Eth-trunk interface. Procedure Run the system-view command to enter the system view. Run the interface interface-type interface-number command to enter the interface view. Run the mirror to observe-server{ both | inbound | outbound } command to configure the remote mirroring interface.

How to configure local interface mirroring on AR series routers
By configuring local interface mirroring, you can replicate the packets transmitted through the interface to local monitoring devices for analysis and surveillance. Before configuring local interface mirroring, ensure that the link protocol state of the interface is Up. 1. Configure the local observing interface. Background In local interface mirroring, monitoring devices are directly connected to the observing interface. It is recommended that other configurations should not be performed on an interface that is configured as the observing interface to prevent its mirroring function from being affected: - If not only the mirroring packets but also the packets of other services are transmitted through the observing interface, the source of the packets cannot be distinguished. - If traffic congests on the observing interface, mirroring packets may be discarded because the priority of the mirroring packets is lower. Procedure Run the system-view command to enter the system view. Run the observe-port interface interface-type interface-number command to configure the local observing interface. 2. Configure the local mirroring interface. Background An interface of any type can be configured as a mirroring interface. If an Eth-trunk interface is configured as a mirroring interface, a member interface of the Eth-trunk interface cannot be configured as a mirroring interface separately. If you want to configure a member interface of the Eth-trunk as a mirroring interface, you must unbind the member interface from the Eth-trunk interface. If a member interface of an Eth-trunk is configured as a mirroring interface, the Eth-trunk interface cannot be configured as a mirroring interface. If you want to configure the Eth-trunk interface as a mirroring interface, you must unbind the member interface that is configured as the mirroring interface from the Eth-trunk interface. Procedure Run the system-view command to enter the system view. Run the interface interface-type interface-number command to enter the interface view. Run the mirror to observe-port { both | inbound | outbound } [ exclude-link-head ] command to configure the local mirroring interface.

How to configure local traffic mirroring on AR series routers
By configuring local traffic mirroring, you can replicate specific packets transmitted through an interface to local monitoring devices for analysis and surveillance. Prerequisites Before configuring local traffic mirroring, ensure that the link protocol state of the interface is Up. 1. Configure the local observing interface. Background In local traffic mirroring, monitoring devices are directly connected to the observing interface. It is recommended that other configurations should not be performed on an interface that is configured as the observing interface to prevent its mirroring function from being affected: - If not only the mirroring packets but also the packets of other services are transmitted through the observing interface, the source of the packets cannot be distinguished. - If traffic congests on the observing interface, mirroring packets may be discarded because the priority of the mirroring packets is lower. Procedure Run the system-view command to enter the system view. Run the observe-port interface interface-type interface-number command to configure the local observing interface. 2. Configure traffic mirroring. Background In traffic mirroring, the mirroring interface applies a traffic policy that includes traffic mirroring behavior. Packets that are transmitted through the interface and match the traffic classification rules are replicated to the observing interface. Procedure a. Configure the traffic classifier. Run the system-view command to enter the system view. Run the traffic classifier classifier-name [ operator { and | or } ] command to create a traffic classifier and enter the view of the traffic classifier. Run the if-match command to configure the matching rule of the traffic classifier based on actual requirements. Run the quit command to quit the view of the traffic classifier. b. Configure the traffic behavior. Run the traffic behavior behavior-name command to create traffic behavior and enter the view of the traffic behavior. Run the mirror to observe-port command to mirror traffic that matches the rule to the specified observing interface. Run the quit command to quit the view of the traffic behavior. Run the quit command to quit the system view. c. Configure the traffic policy. Run the system-view command to enter the system view. Run the traffic policy policy-name command to create a traffic policy and enter the view of the traffic policy, or directly enter the view of an existing traffic policy. Run the classifier classifier-name behavior behavior-name command to configure the traffic behavior of specified traffic classifiers in the traffic policy, that is, bind the traffic behavior to the specified traffic classifier. Run the quit command to quit the view of the traffic policy. Run the quit command to quit the system view. d. Apply the traffic policy. Run the system-view command to enter the system view. Run the interface interface-type interface-number [.subinterface-number ] command to enter the interface view. Run the traffic-policy policy-name { inbound | outbound } to apply the traffic policy in the inbound or outbound direction of the interface.

How to configure remote traffic mirroring on AR series routers
Remote traffic mirroring is only supported in V200R005C32 and earlier versions. By configuring remote traffic mirroring, you can replicate specific packets transmitted through an interface to remote monitoring devices for analysis and surveillance. Before configuring remote traffic mirroring, ensure that the routing protocol and GRE tunnels are configured. 1. Configure the remote observing server. Procedure Run the system-view command to enter the system view. Run the observe-server destination-ip destination-ip-address source-ip source-ip-address [ dscp dscp-value ] command to configure the observing server in remote traffic mirroring. Note: The destination-ip-address parameter indicates the IP address of the monitoring device. The source-ip-address parameter indicates the IP address of the mirroring interface. If the IP addresses of the monitoring device and the mirroring interface are private IP addresses, GRE tunnels must be configured first to ensure the interworking between private IP addresses on public networks. 2. Configure traffic mirroring. Background In traffic mirroring, the mirroring interface applies a traffic policy that includes traffic mirroring behavior. Packets that are transmitted through the interface and match the traffic classification rules are replicated to the observing interface. Procedure a. Configure the traffic classifier. Run the system-view command to enter the system view. Run the traffic classifier classifier-name [ operator { and | or } ] command to create a traffic classifier and enter the view of the traffic classifier. Run the if-match command to configure the matching rule of the traffic classifier. Run the quit command to quit the view of the traffic classifier. b. Configure the traffic behavior. Run the traffic behavior behavior-name command to create traffic behavior and enter the view of the traffic behavior. Run the mirror to observe-port command to mirror traffic that matches the rule to the specified observing interface. Run the quit command to quit the view of the traffic behavior. Run the quit command to quit the system view. c. Configure the traffic policy. Run the system-view command to enter the system view. Run the traffic policy policy-name command to create a traffic policy and enter the view of the traffic policy, or directly enter the view of an existing traffic policy. Run the classifier classifier-name behavior behavior-name command to configure the traffic behavior of specified traffic classifiers in the traffic policy, that is, bind the traffic behavior to the specified traffic classifier. Run the quit command to quit the view of the traffic policy. Run the quit command to quit the system view. d. Apply the traffic policy. Run the system-view command to enter the system view. Run the interface interface-type interface-number [.subinterface-number ] command to enter the interface view. Run the traffic-policy policy-name { inbound | outbound } to apply the traffic policy in the inbound or outbound direction of the interface.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top