Method used to set the IP address of the web LCT computer when logging in to the OSN 8800 on the web LCT

16

Set the computer IP address to be in the same network segment as the equipment IP address. The default network segment is 129.9.X.X.

Other related questions:
Method used to set the gateway IP address for the OSN 8800
In the NE Explorer, click the desired NE and choose Communication > Communication Parameters from the navigation tree. Then set communication parameters such as the IP address.

Command for enabling Web LCT access on Metro 100
:sm-set-lctaces:enable

LCT user password changing on BWS 1600G
The password of the LCT user can be changed only after the LCT user successfully logs in to the LCT NMS.

Can the IP address used to log in to an AR router through the web NMS be an IP address of a VLANIF interface
For AR120 & AR150 series, Eth0/0/0 to Eth0/0/3 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/3 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR160 series and AR509G-L-D-H, GE0/0/0 to GE0/0/3 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/0 to GE0/0/3 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR200 series, AR1220, AR1220V, AR1220W, AR1220VW, and AR1220F, Eth0/0/0 to Eth0/0/7 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/7 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2201-48FE and AR2202-48FE, Eth0/0/0 to Eth0/0/47 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/47 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2204-51GE-P and AR2204-51GE, GE0/0/3 to GE0/0/50 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/3 to GE0/0/50 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2204-27GE-P and AR2204-27GE, GE0/0/3 to GE0/0/26 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/3 to GE0/0/26 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS

Method used to restore the factory settings of the USG6000 on the web UI
You can restore the factory settings on the web UI as follows: The restoration to the factory settings does not affect the saved profiles. 1. Choose System > Profile Management. The information in Current Configuration is the current configuration information. 2. Click Restore factory settings.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top