Can a built-in power supply unit on the S5700-BAT be a lithium battery

17

An S5700-LI-BAT series switch has a built-in AC power supply unit and can use a pluggable power module or a lithium or lead-acid battery for power redundancy.

Other related questions:
Can a built-in power supply unit on the S5700-BAT be a lead-acid battery
An S5700-LI-BAT series switch has a built-in AC power supply unit and can use a pluggable power module or a lithium or lead-acid battery for power redundancy.

Power supply time of batteries on the S5700-BAT
Power supply time (in hours) of batteries on the S5700-LI-BAT: S5700-28P-LI-BAT - When the BAT-4AHA battery is used, the power supply time is 2.4 hours if the switch works with the maximum power consumption; the power supply time is 4.1 hours if the switch works in a typical scenario; the power supply time is 5.6 hours if the switch works with the minimum power consumption. - When the BAT-8AHA battery is used, the power supply time is 4.8 hours if the switch works with the maximum power consumption; the power supply time is 8.2 hours if the switch works in a typical scenario; the power supply time is 11.2 hours if the switch works with the minimum power consumption. S5700-28P-LI-24S-BAT - When the BAT-4AHA battery is used, the power supply time is 1.2 hours if the switch works with the maximum power consumption; the power supply time is 2.1 hours if the switch works in a typical scenario; the power supply time is 4.1 hours if the switch works with the minimum power consumption. - When the BAT-8AHA battery is used, the power supply time is 2.3 hours if the switch works with the maximum power consumption; the power supply time is 4.2 hours if the switch works in a typical scenario; the power supply time is 8.3 hours if the switch works with the minimum power consumption. Notes: - In a typical scenario, 70% of interfaces are in Up state, each interface transmits 10% of maximum traffic, and the EEE function is enabled. - The power supply time shortens when a battery has been used for a long time.

S5700-BAT's support for batteries
S5700-BAT's support for batteries is as follows: An S5700-LI-BAT series switch has a built-in AC power supply unit and can use a pluggable power module or battery for power redundancy. 1. If a battery is configured, the battery can automatically supply power to the switch in cased of a mains power outage, ensuring uninterrupted services. When the AC power supply recovers, the battery automatically turns to the charging state. The S5700-LI-BAT switch supports the following batteries and battery charger module: - BAT-4AHA (chargeable lithium battery) - BAT-8AHA (chargeable lithium battery) - PBB-12AHA (12 AH lead-acid battery charger module connected to an external lead-acid battery with 12 AH of rated capacity) 2. If a power module is configured, the power module can function as a backup of the built-in power supply unit to improve power reliability. The S5700-LI-BAT switch supports the following power modules: - 150 W AC power module - 150 W DC power module To query a switch's support for batteries, see Hardware Query Tool.

How to view the serial number of an S series switch
Serial numbers of S series switches fall into two categories: - Equipment serial number (ESN): indicates the serial number of a switch. The ESN of a modular switch is also called the chassis serial number. - Serial number (SN) of each component: indicates the serial number of a card, subcard, optical module, power supply, or fan module. Select one of the following methods to obtain the ESN or SN of a switch or component: Method 1: View SN labels. Equipment or chassis SN: View the SN label attached to the device panel. (There is a slight difference between label locations on different models. For example, the label can locate on the front, rear, or top of the chassis.) Card serial number: View the SN label on the panel (upper-right or upper-left corner) or PCB (remove and check the card). Method 2: Run a command. Run the display elabel command to view the electronic label of each component. The BarCode field indicates the serial number. Method 3: Through the web system. When the web system is enabled on a device, view the chassis serial number through the web system. EasyOperation web system (supported only in V200R005 and later versions) Log in to a device through the web system and click Monitor on the toolbar to enter the Monitor page. You can view device information, including the chassis serial number. Web system classical version Log in to a device through the web system and click Device Summary on the toolbar to view device information, including the chassis serial number. Click the following links for details about how to query the ESN or SN of a switch or component: - For the S12700, see "Information Collection > Obtaining the Equipment Serial Number" in S12700 Troubleshooting - Preliminary . - For the S7700 and S9700, see "Information Collection > Obtaining the Equipment Serial Number" in S7700&S9700 Troubleshooting - Preliminary . - For the S1720, S2700, S3700, S5700, and S6700, see "Information Collection > Obtaining the Equipment Serial Number" in S1720&S2700&S3700&S5700&S6700 Troubleshooting - Preliminary . - For the S9300, see "Information Collection > Obtaining the Equipment Serial Number" in S9300 Troubleshooting - Preliminary . - For the S600-E, see "Information Collection > Obtaining the Equipment Serial Number" in S600-E Troubleshooting - Preliminary .

Can two power modules of an AR3260 work in active/standby mode
An AR3260is equipped with two 350 W power supply units. The two power supply units work in load balancing mode and provide power to the system simultaneously. -When both two power supply units can work normally, they must work at the same time. That is, they do not support the active/standby mode (one unit is working, and the other is in sleeping state). -When the load power of the system is lower than 350 W, the two power supply units can work in 1+1 backup mode. When one power supply unit fails, the other one can power the router without affecting services on the router. -When the load power of the system is higher than 350 W, the two power supply units cannot work in 1+1 backup mode.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top