Whether S series fixed switches support NDP and NTDP

39

S series switches of V200R005C00 and later versions support NDP and NTDP.

Other related questions:
Whether cards of S series fixed switches support copper modules
The following cards of S series fixed switches support GE copper modules: - ES5D000G4S01 cards (Applicable to S5700-EI series switches. After a GE copper module is installed, the link can go Up. However, you cannot run corresponding commands to configure the rate, duplex mode, auto-negotiation, MDI, flow control, and virtual cable test on the link.) - ES5D00G4SA01 cards (Applicable to S5700-SI and S5710-LI series switches. After a GE copper module is installed, the link can go Up. However, you cannot run corresponding commands to configure the rate, duplex mode, auto-negotiation, MDI, flow control, and virtual cable test on the link.) - ES5D00G4SC00 cards (Applicable to S5700-HI series switches. After a GE copper module is installed, the link can go Up. However, you cannot run corresponding commands to configure the rate, duplex mode, auto-negotiation, MDI, flow control, and virtual cable test on the link.) - ES5D000X2S00 and ES5D000X4S01 cards (Supported by V200R002C00 and later versions, and applicable to S5700-SI series switches.) - ES5D00X2SA00 and ES5D00X4SA00 cards (Supported by V200R002C00 and later versions, and applicable to S5700-HI series switches.) - ES5D21X02S00 cards (Supported by V200R002C00 and later versions, and applicable to S5700-EI series switches.) You can use Hardware Query Tool to query the module types supported by specified cards.

Configure NDP and NTDP to collect EasyDeploy network topology
Configure topology collection on the S series switch, except S1700 as follows: 1. Configure topology collection on the Commander. [HUAWEI] ndp enable [HUAWEI] ntdp enable [HUAWEI] ntdp timer 5 [HUAWEI] easy-operation [HUAWEI-easyoperation] topology enable [HUAWEI-easyoperation] client auto-join enable [HUAWEI-easyoperation] quit 2. Configure the cluster and cluster management VLAN. [HUAWEI] cluster enable [HUAWEI] cluster [HUAWEI-cluster] mngvlanid 10 By default, the management VLAN of a cluster is VLAN 1. It is recommended that you change the management VLAN using command. The management VLAN must be the same as the VLAN on the Commander's interface connected to client.

Cards supported by S series fixed switches
The following S series fixed switches support cards: S3700-HI, S5710-C-LI, S5700-SI (except the S5700-26X-SI-12S-AC), S5700-EI, S5710-EI, S5720-C-EI, S5720-PC-EI, S5700-HI, S5710-HI, S5720-HI, and S6720-EI series switches. Cards must be installed on corresponding switches based on the mapping between them. If a card is installed on an incompatible switch, the card cannot register. You can use Hardware Query Tool to query the card models supported by specified switches.

Link aggregation support on S series fixed switches
S series fixed switches (except the S1700) support the link aggregation function. For details about link aggregation support on the fixed switches, see the "Ethernet Switching - Link Aggregation" in the S1720&S2700&S3700&S5700&S6700 Product Use Precautions.

Whether S series fixed switches support stacking
The Typical Configuration Examples document describes whether each model and version of S series fixed switches (except S1700 switches) supports stacking as well as stack modes, hardware and software requirements, typical networking, and configuration steps. For details, click Typical Configuration Examples and choose Typical Stack Configuration of Fixed Switches- Determining the Stack Connection Mode and Hardware and Software Requirements.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top