By default, users use an IP address to log in to an S series switch through the web.

27

You cannot log in to an S series switch without the MODE key through the web system for the first time.

In the factory setting state, only S series switches that complete first-time configuration through the web system support device login using the IP address:

-S1720: The default IP address of the VLANIF interface is 192.168.1.253/24.

- For S series fixed switches (S1720 excluded), press and hold the MODE button for 6 seconds or longer, and the switch enters the initial configuration mode. By default, the device IP address is set to 192.168.1.253/24.

Note: 192.168.1.253/24 is the IP address for the device login for the first time through the web system. To ensure a successful login, the device must use factory settings. It is recommended that users not log in to the device through a serial interface. Performing any operations through the serial interface will cause a failed login for the first time through the web system. After logging in to the device, users can change the device management IP address on the web page.

Other related questions:
What are the default IP address, user name, and password for logging in to the DEC6001 web page?
Default IP address: 192.168.0.120 Default user name: admin Default password: HuaWei123

Can users who log in to S series switches using the web network management system be authorized through HWTACACS
Users who log in to S series switches using the web network management system cannot be authorized through HWTACACS. The switches support local and remote authentication and authorization for users who log in using the web system. However, the web system supports only two authorization levels: level-0 and non-level-0, which are controlled through local user authorization. If remote authorization is used, the web system cannot obtain the user authority from the local user MIB table and grants the default level-0 authority to the user. HWTACACS authorization fails.

Configure IPSG (for example, configure IP address and MAC address binding) for S series switches on the web page
For details on how to configure IPSG for S series switches (except the S1700) on the web page, see "IPSG Configuration" and "Static User Binding" in Web System Guide.

Can the IP address used to log in to an AR router through the web NMS be an IP address of a VLANIF interface
For AR120 & AR150 series, Eth0/0/0 to Eth0/0/3 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/3 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR160 series and AR509G-L-D-H, GE0/0/0 to GE0/0/3 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/0 to GE0/0/3 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR200 series, AR1220, AR1220V, AR1220W, AR1220VW, and AR1220F, Eth0/0/0 to Eth0/0/7 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/7 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2201-48FE and AR2202-48FE, Eth0/0/0 to Eth0/0/47 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the Eth0/0/0 to Eth0/0/47 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2204-51GE-P and AR2204-51GE, GE0/0/3 to GE0/0/50 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/3 to GE0/0/50 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS. For AR2204-27GE-P and AR2204-27GE, GE0/0/3 to GE0/0/26 are Layer 2 Ethernet interfaces by default, added to VLANIF 1, and configured with a default management IP address 192.168.1.1/24. The AR routers support web NMS access through any interface of the VLANIF based on this IP address. Run the undo portswitch command to change the mode of the GE0/0/3 to GE0/0/26 from Layer 2 to Layer 3. After the management network interface is switched over to the Layer 3 mode, configure the management IP address for the management network interface, and then log in to the web NMS

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top