Method used to view the content of the profile used for the next boot on the USG6000

7

Run the display saved-configuration command to view the content of the profile used for the next boot.

Other related questions:
Method used to view the content of the profile used for the next boot on the USG2000 and USG5000
Run the display saved-configuration command to view the content of the profile used for the next boot.

Method used to view traffic of the USG6000
The method used to view the traffic on the USG6000 is as follows: 1. On the web UI, select traffic logs in monitoring to view traffic logs. 2. On the web UI, select traffic reports in monitoring to view traffic reports.

Method used to view the enabled profile of the USG2000 and USG5000 firewalls
Run the display startup command to view the profiles used for the current boot and the next boot. display startup MainBoard: Configed startup system software: flash:/sup.bin Startup system software: flash:/sup.bin Next startup system software: flash:/sup.bin Startup saved-configuration file: flash:/vrpcfg.zip Next startup saved-configuration file: flash:/vrpcfg.zip Next startup configuration: backup-configuration Startup saved-configuration file/Profile used for the current boot Next startup saved-configuration file/Profile used for the next boot

Method used to view the current configuration of the USG6000
You can run the display current-configuration command to view all configuration commands of the USG firewalls.

Command used on the USG6000 to detect the accessibility of the next hop
The commands used on the USG6000 to detect the accessibility of the next hop are as follows: 1. IP-Link definition IP-Link indicates the link accessibility check. The NGFW periodically sends ICMP echo requests or ARP requests to the specified destination IP address and waits for responses. If no response is received with the specified period of time (3s by default), the firewall considers that the current link is faulty and performs subsequent link-related operations. If the firewall receives three consecutive responses over the original link within the subsequently-specified period of time, the firewall considers that the link fault is eliminated and performs subsequent link recovery-related operations. a. Purposes IP-Link is mainly used to automatically detect whether a service link is normal. It can be used to detect the status of a link that is not directly connected to the NGFW to ensure service continuity. b. Command format [NGFW] ip-link check enable [NGFW] ip-link 1 destination 10.10.1.2 mode icmp [NGFW] ip-link 2 destination 10.10.1.3 mode icmp [NGFW] ip route-static 0.0.0.0 0.0.0.0 10.10.1.2 track ip-link 1 [NGFW] ip route-static 0.0.0.0 0.0.0.0 10.10.1.3 preference 70 track ip-link 2 For details about IP-Link, click link url="http://support.huawei.com/ecommunity/bbs/10248185.html">USG6000 Series Cases for Interworking Between IP-Link and the Hot Standby Devices. 2. Bidirectional forwarding detection (BFD) definition The BFD is used to fast detect communication faults between systems and report the faults to the upper layer protocol in a timely manner. a. Purposes To minimize impacts caused by device faults on services and improve network availability, network devices need to detect faults in communication with adjacent devices in a timely manner to avoid service interruption. The BFD has the following functions: (1) Provide a light-load and fast fault detection mechanism for links between adjacent forwarding engines. The faults include interface faults, data link faults, or even forwarding engine faults. (2) Provide a single mechanism used to detect any media or protocol layer in real time, with wide detection time and overhead ranges. b. Command format (1) The commands used to configure the BFD session are as follows: [NGFW_A] bfd [NGFW_A-bfd] quit [NGFW_A] bfd ab bind peer-ip 10.1.1.2 [NGFW_A-bfd-session-ab] discriminator local 10 [NGFW_A-bfd-session-ab] discriminator remote 20 [NGFW_A-bfd-session-ab] commit (2) The command used to configure the interworking between the static route and BFD session is as follows: [NGFW_A] ip route-static 192.168.1.0 255.255.255.0 10.1.1.2 track bfd-session ab

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top